Handleiding Hilti TE 15-C Boorhamer

Handleiding

2

General safety rules

SAVE THESE INSTRUCTIONS

2. Work Area

2.1 Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

2.2 Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable liquids,

gases, or dust. Power tools create sparks which may

ignite the dust or fumes.

2.3 Keep bystanders, children and visitors away while

operating a power tool. Distractions can cause you to

lose control.

3. Electrical Safety

3.1 Grounded tools must be plugged into an outlet

properly installed and grounded in accordance with

all codes and ordinances. Never remove the ground-

ing prong or modify the plug in any way. Do not use

any adaptor plugs. Check with a qualified electrician

if you are in doubt as to whether the outlet is properly

grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to

carry electricity away from the user.

Applicable only to Class I (grounded) tools.

3.2 Double insulated tools are equipped with a polar-

ized plug (one blade is wider than the other). This plug

will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician to install a

polarized outlet. Do not change the plug in any way.

Double insulation Z eliminates the need for the three-wire

grounded power cord and grounded power supply sys-

tem.

Applicable only to Class II tools.

3.3 Avoid body contact with grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is

an increased risk of electric shock if your body is ground-

ed.

3.4 Don’t expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk of

electric shock.

This instruction need not be provided for tools classified

watertight or splashproof.

3.5 Do not abuse the cord. Never use the cord to car-

ry the tools or pull the plug from an outlet. Keep cord

away from heat, oil, sharp edges or moving parts.

Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

3.6 When operating a power tool outside, use an out-

door extension cord marked «W-A» or «W». These

cords are rated for outdoor use and reduce the risk of

electric shock.

4. Personal Safety

4.1 Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use a

tool while tired or under the influence of drugs, alco-

hol, or medication. A moment of inattention while operat-

ing power tools may result in serious personal injury.

4.2. Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep your hair, clothing,

and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

4.3 Avoid accidental starting. Be sure switch is off

before plugging in. Carrying tools with your finger on the

switch or plugging in tools that have the switch on invites

accidents.

4.4 Remove adjusting keys or wrenches before turn-

ing the tool on. A wrench or a key that is left attached to

a rotating part of the tool may result in personal injury.

4.5 Do not overreach. Keep proper footing and bal-

ance at all times. Proper footing and balance enables

better control of the tool in unexpected situations.

4.6 Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard hat or hearing

protection must be used for appropriate conditions.

5. Tool Use and Care

5.1 Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding

the workpiece by hand or against your body is unstable

and may lead to loss of control.

5.2 Do not force tool. Use the correct tool for your

application. The correct tool will do the job better and

safer at the rate for which it is designed.

5.3 Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with the switch is dan-

gerous and must be repaired.

5.4 Disconnect the plug from the power source

before making any adjustments, changing acces-

sories, or storing the tool. Such preventive safety mea-

sures reduce the risk of starting the tool accidentally.

5.5 Store idle tools out of reach of children and other

untrained persons. Tools are dangerous in the hands of

untrained users.

5.6 Maintain tools with care. Keep cutting tools sharp

and clean.

Properly maintained tools with sharp cutting

edges are less likely to bind and are easier to control.

5.7 Check for misalignment or binding of moving

parts, breakage of parts and any other condition that

may affect the tools operation. If damaged, have the

tool serviced before using. Many accidents are caused

by poorly maintained tools.

5.8 Use only accessories that are recommended by

the manufacturer for your model. Accessories that may

be suitable for one tool may become hazardous when

used on another tool.

6. Service

6.1 Tool service must be performed only by qualified

repair personnel. Service or maintenance performed by

unqualified personnel could result in a risk of injury.

6.2 When servicing a tool, use only identical replace-

ment parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or fail-

ure to follow Maintenance Instructions may create a risk

of electric shock or injury.

Additional Specific Safety Rules:

101 Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

«live» wire will make exposed metal parts of the tool «live»

and shock the operator.

102 Wear ear protectors when using the tool for

extended periods. Prolonged exposure to high intensity

noise can cause hearing loss.

1. WARNING!

Read and understand all instructions.

Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personal injury.

Printed: 07.07.2013 | Doc-Nr: PUB / 5070796 / 000 / 00

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hilti TE 15-C Boorhamer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hilti. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hilti TE 15-C Boorhamer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hilti Boorhamers
Meer handleidingen voor Boorhamers

Veelgestelde vragen over Hilti TE 15-C Boorhamer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hilti TE 30-C-AVR Boorhamer

Handleiding

Hilti TE 4-A22 Boorhamer

Handleiding

Hilti TE 2-A22 Boorhamer

Handleiding

Hilti TE 7-C Boorhamer

Handleiding

Hilti TE 1 Boorhamer

Handleiding

Hilti TE 2 Boorhamer

Handleiding

Hilti TE 30-AVR Boorhamer

Handleiding

Hilti TE 30 Boorhamer

Gerelateerde categorieën