Handleiding Hisense AMD-50UX4RCL4 Airconditioner

Handleiding

5

WARNING

10. Detection of Flammable Refrigerants

• Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks.

• A halide torch (or any other detector using a naked flame) shall not be used.

11. Leak Detection Methods

The following leak detection methods are deemed acceptable for systems containing flammable refrigerants:

• Electronic leak detectors shall be used to detect flammable refrigerants, but the sensitivity may not be

adequate, or may need re-calibration. (Detection equipment shall be calibrated in a refrigerant-free area.)

• Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be calibrated to

the refrigerant employed and the appropriate percentage of gas (25 % maximum) is confirmed.

• Leak detection fluids are suitable for use with most refrigerants but the use of detergents containing

chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper pipe-work.

• If a leak is suspected, all naked flames shall be removed/ extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered from the

system, or isolated (by means of shut off valves) in a part of the system remote from the leak.

• Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the brazing

process.

12. Removal and Evacuation

• When breaking into the refrigerant circuit to make repairs – or for any other purpose

–conventional procedures shall be used.

• However, it is important that best practice is followed since flammability is a consideration.

• The following procedure shall be adhered to:

Remove refrigerant;

Purge the circuit with inert gas;

Evacuate;

Purge again with inert gas;

Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into the correct recovery cylinders.

• The system shall be “flushed” with OFN to render the unit safe.

• This process may need to be repeated several times.

• Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to fill until the

working pressure is achieved, then venting to atmosphere, and finally pulling down to a vacuum.

• This process shall be repeated until no refrigerant is within the system. When the final OFN charge is used,

the system shall be vented down to atmospheric pressure to enable work to take place.

• This operation is absolutely vital if brazing operations on the pipe-work are to take place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

13. Charging Procedures

• In addition to conventional charging procedures, the following requirements shall be followed:

- Ensure that contamination of different refrigerants does not occur when using charging equipment.

- Hoses or lines shall be as short as possible to minimise the amount of refrigerant contained in them.

- Cylinders shall be kept upright.

- Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

- Label the system when charging is complete (if not already).

- Extreme care shall be taken not to overfill the refrigeration system.

- Prior to recharging the system it shall be pressure tested with OFN.

• The system shall be leak tested on completion of charging but prior to commissioning.

• A follow up leak test shall be carried out prior to leaving the site.

14. Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar

with the equipment and all its detail.

It is recommended good practice that all refrigerants are recovered safely.

Safety Precautions

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hisense AMD-50UX4RCL4 Airconditioner. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hisense. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hisense AMD-50UX4RCL4 Airconditioner in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hisense Airconditioners
Meer handleidingen voor Airconditioners

Veelgestelde vragen over Hisense AMD-50UX4RCL4 Airconditioner

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hisense ADT26UX4RBL4 Airconditioner

Handleiding

Hisense HSA25C Airconditioner

Handleiding

Hisense AW0821CW1W Airconditioner

Handleiding

Hisense AP1221CR1W Airconditioner

Handleiding

Hisense HPA30C Airconditioner

Handleiding

Hisense AMD-25UX4RAL4 Airconditioner

Handleiding

Hisense AW1821DR3W Airconditioner

Handleiding

Hisense AP-10CR1SEPS Airconditioner

Gerelateerde categorieën