Handleiding Hitachi CMP4212U Plasma monitor

Handleiding

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Follow all warnings and instructions marked on this monitor.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding- type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use the attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

15. Monitors are designed to comply with the recommended

safety standards for tilt and stability.

Do not apply excessive pulling force to the front, or top, of

the cabinet which could cause the product to overturn

resulting in product damage and/or personal injury.

16. Follow instructions for wall, shelf or ceiling mounting as

recommended by the manufacturer.

17. An outdoor antenna should not be located in the vicinity of

overhead power lines or other electrical circuits.

18. If an outside antenna is connected to the receiver be sure the

antenna system is grounded so as to provide some protection

against voltage surges and built up static charges. Section

810 of the National Electric Code, ANSI/NFPA No. 70-1984,

provides information with respect to proper grounding for the

mast and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding connectors,

location of antenna-discharge unit, connection to grounding

electrodes and requirements for the grounding electrode.

Note to the CATV system installer: This reminder is provided to

call the CATV system installer's attention to Article 820-40 of the

NEC that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be connected to

the grounding system of the building, as close to the point of cable

entry as practical.

Do not place any objects on the top of the monitor which

may fall or cause a child to climb to retrieve the objects.

Disposal of this product may require specific instructions

pertaining to your resident state. For disposal or recycling

information, please contact your local authorities or the

Electronic Industries Alliance: www.eiae.org.

PREVENTION OF SCREEN BURN

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed

(non-moving) patterns can cause permanent damage to the monitor. Such “SCREEN BURNS” constitute misuse and are

NOT

COVERED

by your HITACHI Factory Warranty.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may

require prior authorization from the broadcaster or owner of the video program material.

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

NEC NATIONAL ELECTRICAL CODE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hitachi CMP4212U Plasma monitor. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hitachi. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hitachi CMP4212U Plasma monitor in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hitachi Plasma monitoren
Meer handleidingen voor Plasma monitoren

Veelgestelde vragen over Hitachi CMP4212U Plasma monitor

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hitachi 32PD7800 Plasma monitor

Handleiding

Hitachi CMP5000WXJ Plasma monitor

Handleiding

Hitachi CMP5000WXU-512 Plasma monitor

Handleiding

Hitachi CMP4120HDUS Plasma monitor

Handleiding

Hitachi 42HDM12 Plasma monitor

Handleiding

Hitachi 42HDM70 Plasma monitor

Handleiding

Hitachi 55HDM71 Plasma monitor

Handleiding

Hitachi 42HDM12A Plasma monitor

Gerelateerde categorieën