Handleiding Hitachi N5008AF Tacker

Handleiding

2

9. Before using the power tool, check the push lever.

Before using the power tool make sure to check that

the push lever and valve operate properly. Without

staples loaded into the power tool, connect the hose

and check the following. If the sound of operation

occurs this indicates a fault, so in such a case do not

use the power tool until it has been inspected and

repaired.

䡬 If merely pulling the trigger causes operating

sound of drive bit movement occur, the power

tool is faulty.

䡬 If merely pushing the push lever against the

material to be stapled causes the sound of drive

bit movement to occur, the power tool is faulty.

Furthermore, with regard to the push lever, please

note that it must never be modified or removed.

10. Use specified staples only.

Never use staples other than those specified and

described in these instructions.

11. Be careful when connecting the hose.

When connecting the hose and loading staples in

order not to fire the tool by mistake, make sure of the

followings.

䡬 Do not touch the trigger.

䡬 Do not allow the firing head to contact with any

surface.

䡬 Keep the firing head down.

Strictly observe the above instructions, and always

make sure that no part of the body, hands or

legs is ever in front of the staple outlet.

12. Do not carelessly place your finger on the trigger.

Do not place your finger on the trigger except when

actually stapling. If you carry this tool or hand it to

someone while having your finger on the trigger,

you may inadvertently discharge a staple and thus

cause an accident.

13. Press the staple outlet firmly against the material to

be stapled.

When driving in staples, press the staple outlet

firmly against the material to be stapled. If the outlet

is not applied properly, the staples may rebound.

14. Keep hands and feet away from the firing head

when using.

It is very dangerous for a staple to hit the hands or

feet by mistake.

15. Beware of the tool’s kickback

Do not approach the top of the tool with your head,

etc. during operation. This is dangerous because the

tool may recoil violently if the staple currently being

driven in comes into contact with a previous staple

or a knot in the wood.

16. Take care when stapling thin boards or the corners

of wood.

When stapling thin boards, the staples may pass

right through, as may also be the case when stapling

the corners of wood due to deviation of the staples.

In such cases, always make sure that there is no one

(and nobody’s hands or feet; etc.) behind the thin

board or next to the wood you are going to staple.

17. Simultaneous stapling on both sides of the same

wall is dangerous

Under no circumstances should stapling be

performed on both sides of a wall at the same time.

This would be very dangerous since the staples

might pass through the wall and thus cause injuries.

18. Do not disconnect the hose with your finger on the

trigger.

If you disconnect the hose with your finger on the

trigger, the next time the hose is connected, there

is a danger that the power tool will fire a staple

spontaneously, or operate incorrectly.

19. Disconnect the hose and take out any staples left in

the magazine after use.

Disconnect tool from air before doing tool

maintenance, cleaning a jammed fastener, leaving

work area, moving tool to another location, or after

use. It is very dangerous for a staple to be fired by

mistake.

20. When removing a staple which has become stuck,

make sure to first of all disconnect the hose and

release compressed air.

When removing a staple which has become stuck in

the staple outlet, first of all make sure to disconnect

the hose and release compressed air inside the

power tool.

Accidental firing of the staple could be very

dangerous.

21. A female plug (air socket) should not be used in the

body.

If a female plug is installed in the body, the

compressed air sometimes can not be drawn when

the hose is disconnected so avoid this.

The tool and air supply hose must have a hose

coupling such that all pressure is removed from the

tool when the coupling joint is disconnected.

Type of power Piston reciprocating

Air pressure (Gauge) 4.9 – 8.3 bar (70 – 120 psi.)

Applicable staples Refer to "STAPLE SELECTION" on page 3.

Numbers of loadable staples 120 staples

Size (L×H×W) 323 mm× 280 mm × 86 mm (12-11/16” × 11” × 3-3/8”)

Weight 1.8 kg (4.0 lbs)

Hose (inside diam.) 6 mm (1/4”)

SPECIFICATIONS

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hitachi N5008AF Tacker. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hitachi. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hitachi N5008AF Tacker in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hitachi Tackers
Meer handleidingen voor Tackers

Veelgestelde vragen over Hitachi N5008AF Tacker

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hitachi N5021A Tacker

Handleiding

Hitachi N5024A Tacker

Handleiding

Hitachi N5008AC2 Tacker

Handleiding

Hitachi N5010A Tacker

Handleiding

Hitachi N5008AC Tacker

Handleiding

Hitachi N3804AB2 Tacker

Handleiding

Hitachi N5008AB Tacker

Handleiding

Hitachi N3804AB3 Tacker

Gerelateerde categorieën