8 Channel 2.4 GHz Aircraft Computer Radio System8 Channel 2.4 GHz Aircraft Computer Radio System
Section 3: System Menu Programming Section 3: System Menu Programming
36 37
The tail types you may choose with the Normal wing types are:
NORMAL:
Rudder is located on a vertical stabilizer and elevator is on a horizontal stabilizer.
V-TAIL:
Two control surfaces in a V-conguration operate together providing both yaw (rudder) and pitch
(elevator) control.
Ailevator:
Each half of the elevator is controlled by a dedicated servo to provide pitch (elevator), and roll (aileron) control.
The tail types you may choose with delta wing types are:
None: For ying wing models without a rudder.
1Servo: For ying wing models with a single rudder servo.
2Servo: For ying wing models with dual rudder servos.
Model Type GLID Menu Programming cont.
4. In the GLID setup menu, you will set your wing and tail choices.
Scroll to “WING” and press the jog dial to activate the menu.
The choices for Normal GLID wing type are:
1AILE: Single aileron servo
1AILE+1FLAP: Single aileron servo and single ap servo
1AILE+2FLAP: Single aileron servo and two ap servos
2AILE: Two aileron servos
2AILE+1FLAP: Two aileron servos and one ap servo
2AIL+2FLAP: Two aileron servos and two ap servos
Additionally there are setups for Delta (Elevon) wing type models:
2AILE: Two elevon servos
2AILE+1FLAP: Two elevon servos and one ap servo
2AILE+2FLAP: Two elevon servos and two ap servos
5. Once you have selected your wing type, press the jog dial to conrm your selection.
6. Scroll to “TAIL” and press the jog dial to activate the menu.
The choices for tail type are dependent on the type of wing you
selected.
7. Select the tail type for your model and press the jog dial to
conrm your selection.
8. Use the back button to return to the System Menu.
Model Type HELI Menu Programming
1. From the System Menu select MDL TYPE.
2. Press the jog dial once to enter the Model Type Selection
Menu.
3. Scroll to highlight “HELI” and press the jog dial to enter the
HELI setup menu.
4. In the HELI menu you will set the swash type. Scroll to
highlight “SWASH” and press the jog dial to activate the menu.
There are six types of Swash types to choose from:
- 90° 1 servo: The three swash servos are congured 90° apart, and each servo provides independent
control of collective, pitch, or roll.
- 120° 3 servos: The three swash servos are congured 120° apart, and all servos operate in unison to
control collective, pitch, and roll.
- 140° 3 servos: The three swash servos are congured 140°/140°/80° apart, and all servos operate in
unison to control collective, pitch, and roll.
- 180° 2 Servo: In case of when the swash is formed in 90° angle and two servos control the mixing of
aileron and pitch.
- 90° 3 Servo: In case of when the swash is formed in 90° angle and three servos control the mixing of
aileron, elevator, and pitch.
- 90° 4 Servo: In case of when the swash is formed in 90° angle and four servos control the mixing of
aileron, elevator, and pitch.
Your helicopter’s manual will indicate the type of swashplate on your model.
5. Select the swash type for your helicopter and press the jog dial to conrm your selection.
6. Press the back button to return to the System Menu.
Praat mee over dit product
Laat hier weten wat jij vindt van de Hitec Flash 8 RC Controller. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.