Handleiding Hunter 19090 Squire Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN / INSTRUCTIONS D‘INSTALLATION

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety.

It is very important that they are read carefully

and completely before beginning installation

of the lighting xture.

•

WARNING

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para

su seguridad. Es muy importante leerlas

detenidamente y completamente antes de

comenzar la instalación de la lámpara.

•

•

Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

• L‘appareil d‘éclairage doit être mis à la terre.

Si le l de terre du lieu d‘installation n‘est pas

présent, ARRÊTEZ immédiatement l‘installation

et consultez un électricien qualié.

• Todo el cableado debe realizarse de acuerdo

con los códigos eléctricos locales y nacionales

ANSI/NFPA 70. Si no está familiarizado con

el cableado, o si tiene duda, consulte a un

electricista calicado.

ADVERTENCIA

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre

sécurité. Il est très important de les lire

attentivement dans leur intégralité avant

d‘entreprendre l‘installation du luminaire.

•

AVERTISSEMENT

• Pour éviter tout choc électrique, avant

d‘installer le luminaire, coupez le courant en

éteignant les disjoncteurs de la boîte électrique

associée à l‘interrupteur mural.

• Le luminaire doit être mis à la terre. Si le l

de terre du lieu d‘installation n‘est pas présent,

ARRÊTER immédiatement l‘installation et

consulter un électricien qualié.

• Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et

à la norme ANSI/NFPA70. Si vous n‘avez pas

l‘habitude de faire ce câblage ou en cas de doute,

adressez-vous à un électricien qualié.

ENGLISH

Squire Manor

Here are the

tools you‘ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l‘installation:

Ladder

Escalera

Échelle

Pliers

Alicates

Pince

Wire Strippers

Pelacables

Pince à dénuder

Twist or tape wire

ends together to make

it easier to thread

through downrod.

Hunter Pro Tip:

NOTICE

In order to use a 12in rod by itself

you must rst remove the post

from the 6in rod and install it on

one of the ends of the 12in rod.

KC04601119

KC04602214

Brushed Nickel

Níquel Pulido

Nickel Brossé

Matte Black

Negro Mate

Noir Mat

19090

19091

Part #/Pieza #/Pièce #

Hardware Service Kit / Kit De Mantenimiento Del Equipo /

Trousse De Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

NOTICE

Drill 9/64" pilot holes in

support structure to aid in

securing light xture.

Drill

Taladro

Foret

Screwdriver

Destornilladore

Tournevis

Fixture weight ±2 lbs:

Peso ±2 lbs:

Poids xe ±2 lbs:

5 Light Linear Chandelier

5 Luz Lámpara Lineal

5 Lumière Chandelier Linéaire

6.31 lbs (2.86 kg)

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old

xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag.

Remove decorative nuts (N) from mounting screws (A). Mounting plate (B) contains several pairs of threaded holes. Find

the pair of holes that matches the spacing in the holes on the xture‘s canopy. Attach two mounting screws (A) to the

mounting plate (B). Tighten nuts (C) to hold the screws in place. Put the hollow rubber plug (H) inside the hole in the

ceiling, then insert the tapping screw (I) through the mounting plate (B) into the rubber plug (H). Place the mounting

plate (B) over the junction box so that mounting screws (A) and nuts (C) are visible. Pull the house wires through the

center of mounting plate (B). Secure mounting plate (B) to the junction box by tightening the screws (D).

ASSEMBLING THE FIXTURE

There are 4 12-inch rods (P), and 1 6-inch rod (Q) included for each side of the xture. Determine the correct number

of rods needed for proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the

wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods

off the xture‘s wiring to discard. Keep in mind that you must use at least one rod to hang the xture. Thread the wires

through the rods and pull the wires until taut before connecting the rods together. Place cup (R) onto threaded post (S)

and screw rod onto threaded post (S) on the xture. Place reinforcing plate (M) inside canopy (G) and the canopy (G) over

the threaded post (O) of the top rod. Put one side of threaded post (O) though the wirerope noose (F) and washer (L). Lock

the reinforcing plate and canopy by screwing wingnut (K) onto threaded post (O). Hide wirerope inside the canopy (G).

Attach screw collar loop (J) onto mounting plate (B).

CONNECTING THE WIRES

Have a helper support the xture‘s weight while completing the wiring.

Attach the xture‘s wires to the power supply wires from the junction

box. Connect black to black (Live); white to white (grounded); grounding

to grounding (green or copper). Twist the ends of the wire pairs together.

Then, twist on a wire connector. Make sure all twists are in the same

direction. Loop xture‘s ground wire around grounding screw (E) and

tighten. If there is no ground wire (green or copper) from the junction

box, contact a qualied electrician.

FINISHING THE INSTALLATION

Raise canopy (G) to mounting plate (B) and position mounting screws (A) so that they protrude through the openings of

canopy (G). Secure canopy (G) in place with decorative nuts (N). Slide candle sleeves (T) onto sockets (U). Install light bulb

(not included) in accordance with the xture‘s specications. Do not exceed the recommended wattage. Your installation

is now complete. Turn on the power and test the xture.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light

and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

19090

19091

©2020 Hunter Fan Co. ML036

r_112320

Part #/Pieza #/Pièce #

Hardware Service Kit / Kit De Mantenimiento Del Equipo /

Trousse De Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

For Models:

Para los Modelos:

Pour les Modèles:

H

I

K

L

M

N

E

D

C

B

A

G

F

J

O

R

P

S

Q

T

U

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19090 Squire Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19090 Squire Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Veelgestelde vragen over Hunter 19090 Squire Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.