Handleiding Hunter 19280 Teren Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION

For Models:

Para los Modelos:

Pour les Modèles:

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Ladder

Escalera

Échelle

Pliers x2

Alicates x2

Pince x2

Wire Strippers

Pelacables

Pince à dénuder

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety. It

is very important that they are read carefully and

completely before beginning installation of the

lighting xture.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para su

seguridad. Es muy importante leerlas detenid-

amente y completamente antes de comenzar la

instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre sécurité.

Il est très important de les lire attentivement dans

leur intégralité avant d’entreprendre l’installation

du luminaire.

Fixture weight ±2 lbs:

Peso ±2 lb:

Poids xe ±2 lbs:

•

WARNING

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

• Todo el cableado debe realizarse de acuerdo con

los códigos eléctricos locales y nacionales ANSI/

NFPA 70. Si no está familiarizado con el cableado,

o si tiene duda, consulte a un electricista calicado.

• Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

•

ADVERTENCIA

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation et

consultez un électricien qualié.

•

AVERTISSEMENT

•

Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et à la

norme ANSI/NFPA70. Si vous n'avez pas l'habitude

de faire ce câblage ou en cas de doute, adressez-

vous à un électricien qualié.

• Pour éviter tout choc électrique, avant d’installer

le luminaire, coupez le courant en éteignant les

disjoncteurs de la boîte électrique associée à

l’interrupteur mural.

•

Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

Part #/Pieza #/Pièce #

Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De

Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

Glass/Domo De Vidrio/Verre

Type/Tipo/Type

©2021 Hunter Fan Co.

Part #/Pieza #/Pièce # Model/Modelo/ Modèle

ENGLISH

Light Chandelier

Luz Lámpara Tipo Araña

Lumière Chandelier

Screwdriver

Destornilladore

Tournevis

Twist or tape wire ends

together to make it

easier to pass them

through the downrods.

Threaded post may also

be removed for easier

wire access.

Hunter Pro Tip:

Let the tool do the

work! Use chain pliers

to easily open and

close chain links to

shorten your xture.

Hunter Pro Tip:

F

G

H

I

J

K

L

M

O

N

P

Q

R

S

C

D

B

A

E

19280

19855

Teren

KD83901L19

KD83901L16

Textured Rust/Óxido

Texturado/Rouille Texturée

Distressed White/Blanco

Envejecido/Blanc Patiné

19280

19855

ML127

R_082421

8.77 lbs (3.98 kg)

6

6

6

FINISHING THE INSTALLATION

CONNECTING THE WIRES

ASSEMBLING THE FIXTURE

PREPARING FOR INSTALLATION

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for

deep cleaning. For regular cleaning, turn off the light and wipe down

the xture with a clean lint-free cotton or microber cloth. Never spray

cleaner directly onto the xture.

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the

old xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from

the bag. One end of the threaded post (D) should be attached to the mounting bracket (A) with a hex nut (E) in place.

The other end should have the canopy loop (G) attached. Unscrew the canopy loop ring (H) from the canopy loop (G).

Depending on the placement of your junction box the position of threaded post (D) may need to be adjusted to allow

the canopy to be ush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and

place canopy (F) over the canopy loop (G), so that it is ush with the ceiling. Adjust the position of threaded post (D)

on the mounting bracket (A) so that the canopy (F) covers at least half of the exterior threads on the canopy loop (G)

while it is securely connected to threaded post (D). The threaded post (D) can be adjusted by loosening hex nut (E)

to allow movement of threaded post (D) on mounting bracket (A). Once the ideal position of the threaded post (D) is

determined, tighten up the hex nut (E) onto the threaded post (D) just beneath the mounting bracket (A) to secure the

threaded post in place.

Adjust the xture arms to the proper position (see drawing 1). Adjust the position of the hex nut (N) at the lower end

of center rod (M). Thread wires through center rod (M) then screw the center rod (M) into the hex post (O) of the xture.

Slide the center column (L) over center rod (M), threading wires through rod and hanging ring (K) and secure at the top

with the hanging ring (K). Screw the threaded post (Q) into the hex post (P), slide the decorative column (R) onto the

threaded post (Q), then screw nial (S) onto threaded post (Q) to secure.

By measuring, determine the correct number of chain links needed for proper hanging height. If necessary, use a pair

of pliers to open and remove any excess chain. Attach one quick-connect link (J) to each end of chain (I). Use one quick-

connect link (J) to attach chain (I) to hanging ring (K) and securely close. Feed the xture wires up through the chain

(every three links or so), pulling the wires until taut. Slide canopy loop ring (H) and canopy (F) onto the chain/wire and

thread wires through canopy loop (G). Use the remaining quick-connect link (J) to attach chain (I) to canopy loop (G).

To shorten the xture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired

length. Have a helper support the xture’s weight and attach the mounting bracket (A) to the junction box by securely

tightening the mounting screws (C).

Attach the xture’s wires to the power supply wires from the junction

box. Connect black to black (Live); white to white (grounded);

grounding to grounding (green or copper). Twist the ends of the wire

pairs together. Then, twist on a wire connector. Make sure all twists are

in the same direction. Loop xture’s ground wire around grounding

screw (B) and tighten. If there is no ground wire (green or copper) from

the junction box, contact a qualied electrician.

Place the canopy (F) ush to the ceiling and slide the canopy loop ring (H) up beneath the canopy. Tightly screw canopy

loop ring (H) onto the canopy loop (G) to properly secure the canopy (F) in place. Install light bulb (not included) in

accordance with the xture’s specications. Do not exceed the recommended wattage. Turn on the power and test the

xture. Your installation is now completed.

1

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19280 Teren Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19280 Teren Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Hunter 19280 Teren Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hunter 19263 Felippe Lamp

Handleiding

Hunter 19150 Devon Park Lamp

Handleiding

Hunter 19330 Langwood Lamp

Handleiding

Hunter 19712 Lochemeade Lamp

Handleiding

Hunter 19127 Astwood Lamp

Handleiding

Hunter 19995 Gablecrest Lamp

Handleiding

Hunter 19249 Cypress Grove Lamp

Handleiding

Hunter 19073 Bluff View Lamp

Gerelateerde categorieën