Handleiding Hunter 19345 Van Nuys Lamp

Handleiding

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION

For Models:

Para los Modelos:

Pour les Modèles:

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Ladder

Escalera

Échelle

Pliers

Alicates

Pince

Wire Strippers

Pelacables

Pince à dénuder

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety. It

is very important that they are read carefully and

completely before beginning installation of the

lighting xture.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para su

seguridad. Es muy importante leerlas detenid-

amente y completamente antes de comenzar la

instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre sécurité.

Il est très important de les lire attentivement dans

leur intégralité avant d’entreprendre l’installation

du luminaire.

Fixture weight ±2 lbs:

Peso ±2 lb:

Poids xe ±2 lbs:

•

WARNING

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

• Todo el cableado debe realizarse de acuerdo con

los códigos eléctricos locales y nacionales ANSI/

NFPA 70. Si no está familiarizado con el cableado,

o si tiene duda, consulte a un electricista calicado.

• Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

•

ADVERTENCIA

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation et

consultez un électricien qualié.

•

AVERTISSEMENT

•

Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et à la

norme ANSI/NFPA70. Si vous n'avez pas l'habitude

de faire ce câblage ou en cas de doute, adressez-

vous à un électricien qualié.

• Pour éviter tout choc électrique, avant d’installer

le luminaire, coupez le courant en éteignant les

disjoncteurs de la boîte électrique associée à

l’interrupteur mural.

•

Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

Part #/Pieza #/Pièce #

Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De

Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

Glass/Domo De Vidrio/Verre

Type/Tipo/Type

©2021 Hunter Fan Co.

Light Pendant

Luz Colgante

Lumière Chaînette

Part #/Pieza #/Pièce # Model/Modelo/ Modèle

ENGLISH

NOTICE

In order to use a 12in rod by

itself you must rst remove

the post from the 6in rod and

install it on one of the ends of

the 12in rod.

Screwdriver

Destornilladore

Tournevis

Twist or tape wire ends

together to make it

easier to pass them

through the downrods.

Threaded post may also

be removed for easier

wire access.

Hunter Pro Tip:

J

I

L

M

N

O

P

Q

A

D

G

H

B

C

E

F

19345

19346

Van Nuys

KD81301L11

KD81301214

Alturas Gold/Alturas Gold/Or

d’Alturas

Brushed Nickel/Níquel Pulido/

Nickel Brossé

19345

19346

KD50901147

Clear Glass/Vidrio

Transparente/

Verre Transparent

19345

19346

ML110

R_063021

7.65 lbs (3.47 kg)

1

1

1

FINISHING THE INSTALLATION

CONNECTING THE WIRES

ASSEMBLING THE FIXTURE

PREPARING FOR INSTALLATION

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep

cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray

cleaner directly onto the xture.

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the

old xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from

the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place.

The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop

(E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to

allow the canopy to be ush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box

and place canopy (D) over the canopy loop (E), so that it is ush with the ceiling. Adjust the position of threaded post

(H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop

(E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G)

to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is

determined, tighten up the hex nuts (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the

threaded post in place.

There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each xture. Determine the correct number of rods needed

for proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the wires to desired

length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the xture’s

wiring to discard. Keep in mind that you must use at least one rod to hang the xture. Thread the wires through the

rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (L) on the xture.

Carefully install glass shade (O) to center column (N) with thumbscrews (M) and tighten up the glass shade. Secure the

bottom trim ring (Q) by screwing the cap nuts (P). Pull the xture wires through the canopy loop ring (F), canopy loop

(E) and the top of canopy (D). Screw the threaded post of the top rod to canopy loop (E) then attach canopy loop (E) to

threaded post (H). Have a helper support the xture’s weight and attach the mounting bracket (A) to the junction box by

securely tightening the mounting screws (B).

Attach the xture’s wires to the power supply wires from the junction

box. Connect black to black (Live); white to white (grounded);

grounding to grounding (green or copper). Twist the ends of the wire

pairs together. Then, twist on a wire connector. Make sure all twists are

in the same direction. Loop xture’s ground wire around grounding

screw (C) and tighten. If there is no ground wire (green or copper) from

the junction box, contact a qualied electrician.

Place the canopy (D) ush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy

loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Install light bulb (not included)

in accordance with the xture’s specications. Do not exceed the recommended wattage. Your installation is now

completed. Turn on the power and test the xture.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Hunter 19345 Van Nuys Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Hunter. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Hunter 19345 Van Nuys Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Hunter Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Hunter 19345 Van Nuys Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Hunter 19207 Grove Isle Lamp

Handleiding

Hunter 19303 Van Nuys Lamp

Handleiding

Hunter 19775 Lochemeade Lamp

Handleiding

Hunter 19294 Van Nuys Lamp

Handleiding

Hunter 19333 Langwood Lamp

Handleiding

Hunter 19569 Maple Lamp

Handleiding

Hunter 19001 Astwood Lamp

Handleiding

Hunter 19285 Highland Hill Lamp

Gerelateerde categorieën