Handleiding Intergas Compact HRE 24 SB CV-ketel

Handleiding

3

2.1 Operating mode on the service display:

—

Off (appliance frost protection active)

3

Ventilate

Wait mode

4

Ignite

0

CH pump post run

5

CH mode

1

Desired temperature reached

6

DHW mode

2

Self test

7

Heat up appliance on (not applicable for Compact HRE SB)

Note: When the red LED above the reset key flashes a fault has occurred. A fault code will then appear on the temperature/clock display.

2.2 Changing the settings of the various functions

Keeping the key pressed for 2 seconds takes you to the user settings menu (LED at and the display starts to flash).

Then each time you press the key a different function LED will start to flash. The value of the function can be set using the

and keys. The value set is displayed on the display.

 The reset key closes the settings menu and stores the changes.

 If no key is pressed for 30 seconds, the settings menu is automatically closed and the changes are stored.

 The on/off key closes the settings menu without storing the changes.

 The button restores the default setting for the switch moments (hold for 5 seconds).

 By pressing the or keys the clock can be set and the switch moments can be defined.

 By pressing the button 2 time blocks can be programmed in which the CH is on (switch moments 1 to 4).

 By pressing the button the new times will be stored in the boiler controller. In the display appears [P] for a short period.

 Pressing the button for less than 1 second the following additional functions can be activated:

1. t-on (temporary on), the boiler will respond on every CH demand from the room thermostat until the next switch moment.

2. c-on (continuous on), the boiler will respond on every CH demand from the room thermostat without any time limit.

3. OFF, the boiler will not respond on any CH demand from the room thermostat.

The maximum CH supply temperature. Can be set between 30°C and 90°C (standard setting 80°C).

Low setting for moderately cold weather, high setting for colder weather.

DHW temperature. The temperature in the DHW storage cylinder can be set, if it is connected to an external sensor,

between 40°C and 65°C (standard setting 60°C). To prevent the growth of legionella it is advised not to set the DHW

temperature below 60°C.

All other alterations of settings of the boiler may only be carried out by your installer.

3 START-UP

Once the appliance has been connected to water, gas and electricity supplies and

checked by an authorised installer, the appliance can be started.

Please check the following points:

 The central heating system and domestic hot water system must be well filled and bled.

 The appliance must be switched off (Horizontal dash on service display, other LEDs off).

 The water pressure in the central heating system must be between 1 and 2 bar (Shown on the temperature display).

Never switch the appliance on if the appliance, the CH system and the DHW system have not been completely filled and bled.

 The room thermostat must be set below the temperature in the room.

 The gas tap must be open.

 Switch the appliance on with the on/off key in the display (The LED lights up, and the service display goes out). The appliance

may now heat up for purposes of the DHW system until the heat exchanger reaches the set temperature.

 Set the clock and the switch moments. If the boiler is in a time block that CH is not active the boiler must be set in c-on (see §2.2).

 Set the room thermostat higher than the actual room temperature. The appliance will fire for purposes of the CH system.

4 FAULTS

If the following simple appliance faults occur, they can be resolved as follows. In the case of repeated occurrence or other faults

always notify your installer.

1. The CH system does not heat up or does not become sufficiently warm:

 Increase the temperature setting at the room thermostat.

 Open the radiator valves.

 Increase the CH water temperature setting using the and the and key on the operating panel (see §2).

 Bleed the appliance and installation and check the CH water pressure.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Intergas Compact HRE 24 SB CV-ketel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Intergas. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Intergas Compact HRE 24 SB CV-ketel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Intergas CV-ketels
Meer handleidingen voor CV-ketels

Veelgestelde vragen over Intergas Compact HRE 24 SB CV-ketel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Intergas Compact HRE 18 OV CV-ketel

Handleiding

Intergas Combi Compact ECO RF 36 CV-ketel

Handleiding

Intergas Compact HRE 40 SB CV-ketel

Handleiding

Intergas Kombi Kompakt HRE CV-ketel

Handleiding

Intergas Kompakt Solo HRE 30 CV-ketel

Handleiding

Intergas H22VR.W CV-ketel

Handleiding

Intergas Combi Compact ECO RF 30 CV-ketel

Handleiding

Intergas Kombi Kompakt HR 28 CV-ketel

Gerelateerde categorieën