Handleiding JET JWDP-12 Kolomboormachine

Handleiding

1.0 IMPORTANT SAFETY

INSTRUCTIONS

WARNING – To reduce risk of injury:

1. Read and understand the entire owner’s manual

before attempting assembly or operation.

2. Read and understand the warnings posted on the

machine and in this manual. Failure to comply with

all of these warnings may cause serious injury.

3. Replace the warning labels if they become

obscured or removed.

4. This drill press is designed and intended for use by

properly trained and experienced personnel only. If

you are not familiar with the proper and safe

operation of a drill press, do not use until proper

training and knowledge have been obtained.

5. Do not use this drill press for other than its

intended use. If used for other purposes, JET

disclaims any real or implied warranty and holds

itself harmless from any injury that may result from

that use.

6. Always wear ANSI Z87.1 approved safety glasses

or face shield while using this drill press. (Everyday

eyeglasses only have impact resistant lenses; they

are not safety glasses.)

7. Before operating this machine, remove tie, rings,

watches and other jewelry, and roll sleeves up past

the elbows. Do not wear loose clothing. Confine

long hair. Non-slip footwear or anti-skid floor strips

are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during

extended periods of operation.

9. Some dust created by power sanding, sawing,

grinding, drilling and other construction activities

contain chemicals known to cause cancer, birth

defects or other reproductive harm. Some

examples of these chemicals are:

10. Lead from lead based paint.

11. Crystalline silica from bricks, cement and other

masonry products.

12. Arsenic and chromium from chemically treated

lumber.

13. Your risk of exposure varies, depending on how

often you do this type of work. To reduce your

exposure to these chemicals, work in a well-

ventilated area and work with approved safety

equipment, such as face or dust masks that are

specifically designed to filter out microscopic

particles.

14. Do not operate this machine while tired or under

the influence of drugs, alcohol or any medication.

15. Make certain the switch is in the OFF position

before connecting the machine to the power

supply.

16. Make certain the machine is properly grounded.

17. Make all machine adjustments or maintenance with

the machine unplugged from the power source.

18. Remove adjusting keys and wrenches. Form a

habit of checking to see that keys and adjusting

wrenches are removed from the machine before

turning it on.

19. Keep safety guards in place at all times when the

machine is in use. If removed for maintenance

purposes, use extreme caution and replace the

guards immediately.

20. Make sure the drill press is firmly secured to the

floor or bench before use.

21. Check damaged parts. Before further use of the

machine, a guard or other part that is damaged

should be carefully checked to determine that it will

operate properly and perform its intended function.

Check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting and any

other conditions that may affect its operation. A

guard or other part that is damaged should be

properly repaired or replaced.

22. Provide for adequate space surrounding work area

and non-glare, overhead lighting.

23. Keep the floor around the machine clean and free

of scrap material, oil and grease.

24. Don't use in dangerous environment. Don't use

power tools in damp or wet locations, or expose

them to rain. Keep work area well lighted.

25. Keep visitors a safe distance from the work area.

Keep children away.

26. Make your workshop child proof with padlocks,

master switches or by removing starter keys.

27. Give your work undivided attention. Looking

around, carrying on a conversation and “horse-

play” are careless acts that can result in serious

injury.

28. Maintain a balanced stance at all times so that you

do not fall or lean against the spindle or other

moving parts. Do not overreach or use excessive

force to perform any machine operation.

29. Use the right tool at the correct speed and feed

ra

t

e. Do not force a tool or attachment to do a job

for which it was not designed. The right tool will do

the job better and more safely.

30. Use recommended accessories; improper

accessories may be hazardous.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je JET JWDP-12 Kolomboormachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met JET. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van JET JWDP-12 Kolomboormachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor JET Kolomboormachines
Meer handleidingen voor Kolomboormachines

Veelgestelde vragen over JET JWDP-12 Kolomboormachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.