K-Cup® Pod Holder
To remove the K-Cup® pod holder from
the brewer, lift the handle and grasp
the top of the K-Cup® pod holder
with one hand while pushing up on
the bottom of the K-Cup® pod holder
from underneath with the other until
it releases. After cleaning, align the
K-Cup® pod holder with the opening,
using the two front ribs as a guide,
and snap into place from the top.
Funnel
Washing the funnel ensures a fresh
beverage experience. The funnel
should be washed regularly and can
be removed from the K-Cup® pod
holder by pulling on it until it pops off.
To replace it, orient the snaps to the
indent and just snap it back onto the
K-Cup® pod holder.
STRONG
Exit Needle
Remove the pod holder assembly
and detach the funnel. Locate the
exit needle on the inside bottom
of the K-Cup® pod holder. Insert a
straightened paper clip into the exit
needle to loosen any coffee grounds.
Entrance Needles
Lift the brewer handle and locate the
entrance needles on the underside of the
lid. To clean the holes in the needles, hold
the brewer handle in the upward position
and with your other hand, carefully insert
a straightened paper clip into all the
holes. Gently move it around to loosen
any coffee grounds. Lower the handle
completely and run a cleansing brew two
times. Do not insert a K-Cup® pod.
CAUTION: There are sharp needles that puncture the K-Cup® pod above the
K-Cup® pod holder and in the bottom of the K-Cup® pod holder. To avoid risk of
injury, do not put your fingers in the K-Cup® pod holder.
NOTE: Always remove and dispose of the used K-Cup® pod after brewing.
You should descale your brewer every 3 months or when the descale
notification turns on. Properly follow the descaling procedure in order
to turn off the notification.
Depending on the mineral content of your water, calcium deposits
or scale may build up in your brewer. Scale is nontoxic, but if left
unattended it can hinder brewer performance. Regularly descaling
your brewer every 3 months helps maintain the heating element and
other internal parts that come in contact with water. Calcium deposits
may build up faster, making it necessary to descale more often.
Descaling Procedure
Before you begin, you will need a large ceramic mug, fresh water,
Keurig® Descaling Solution, and access to a sink. Do not use a
paper cup. Ensure that there is no beverage pod in the K-Cup® pod
holder. Please allow approximately 15-20 minutes for the descaling
procedure.
STEP 1: Prepare the Brewer
When the Descale notification appears on the screen, press the left
arrow, then choose CONTINUE. Select your descaling product:
2 oz pouch or 14 oz bottle. Next, follow the prompts on the screen to
complete the descale process. If you would like to descale your brewer
but don’t see the descale notification on the display, press both
arrows at the same time to open Settings, then select Descale Mode.
Note: Make sure to remove the water filter from the water reservoir if applicable.
STEP 2: Descale the Brewer
Empty the water reservoir and add the Keurig® Descaling Solution
to the water reservoir. Pour the entire bottle of Keurig® Descaling
Solution into an empty water reservoir. If using the bottle, fill the
empty bottle with water and pour into the water reservoir. If using
the pouch, add 3 cups of water (24 oz) to the reservoir. Do not insert
a K-Cup® pod. Place a large mug on the drip tray.
Press the flashing BREW button to dispense 12 oz of hot water.
Discard the hot water and replace mug on the drip tray. Repeat until
the water reservoir is empty and the screen says ADD WATER.
STEP 3: Fresh Water Rinse
Rinse the water reservoir and refill it to the MAX fill line with fresh
water. Make sure the mug is on the drip tray. When the BREW button
flashes, press to begin fresh water rinse. Once the brew is complete,
pour the hot liquid into the sink. Repeat this step until the screen says
DESCALE COMPLETE. Now the brewer is ready for use.
NOTE: The cleaning action of Keurig® Descaling Solution may result in a “foam” dispensed from the
brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled,
the brewer may not fill properly after the descaler is added. If this occurs, you may see little to no output
dispensed, followed by the sound of air blowing out. If this occurs:
• Turn off and unplug the brewer.
• If there is Keurig® Descaling Solution in the water reservoir, discard the contents, rinse the water reservoir
thoroughly, and refill with water.
• Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse cycle. The brewer should
begin to function normally as the solution is rinsed out and the scale is removed. If problem persists,
allow brewer to sit unplugged for at least 30 minutes before continuing with the rinse.
Descaling Your Brewer
Praat mee over dit product
Laat hier weten wat jij vindt van de Keurig K-Supreme Smart Koffiezetapparaat. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.