Handleiding Kichler 15326AZT Center Lamp

Handleiding

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

This xture is intended for installation in accordance with the National

Electric Code (NEC) and Local code specications. Failure to adhere to

these codes and instructions may result in serious injury and/or property

damage and will void the warranty.

1) WARNING: This xture is not to be installed within 10 feet (3M) of a pool,

spa or fountain.

2) This xture is to be used only with a power unit (transformer) rated a

maximum of 300 W (25 AMPS) 15 volts.

3) The #18 ga. xture wire is not intended for direct burial.

4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath

the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’

(76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M), 15506-BK.

5) Fixture shall not use a tungsten halogen lamp unless the xture is marked

for use with such lamps.

6) Wiring connections must be made with approved/listed wire connection

device(s) suitable for the application. Do not exceed manufacturers’ wiring

combination specications for size and quantity of conductors.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting xture.

2) At desired location, hammer stake (A) into ground. To avoid damage to

stake, place a board on top of stake while hammering. If ground is hard

and stake is difcult to install, make a crosscut in ground using a at

shovel.

3) Clear away area in ground at wireway slot in top of stake (A).

4) Screw stake adapter (B) onto end of stem (C).

5) Run 12V cable from xture body (D) through stem (C).

6) Screw stem (C) into xture body (D).

7) Lay 12V cable into wireway slot and screw stem (C) into stake (A). If

assembly does not look straight, adjust by pushing or pulling on stake only.

8) Install provided lamp (E) to socket inside xture body (D).

9) Align threaded holes in roof (G) with holes at ends of spokes (H).

10) Secure roof (G) in place using thumbscrews (J).

11) TURN OFF POWER.

12) Make wire connections using supplied Quic Disc

™

following instructions

below, or using other approved wiring connection method (not supplied.)

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

Date Issued: 12/2/11 IS-15326-US

A

J

C

G

D

E

QUIC DISC

™

WIRING INSTRUCTIONS

Turn off power.

The full length of the 18 GA xture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:

• Wiring is to be protected by routing close to the xture or accessory or secured to a building structure such as house or deck.

• 18 GA xture wiring is to be cut off so that it is attached to the connector within 6 inches of the xture or building structure.

• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA xture wire is to be buried.

The Quic Disc

™

connector is designed to install one xture and accommodates one 18 GA xture wire and one 10 GA or one 12 GA supply wire.

Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc

™

or place the 12 gauge supply wire across the area marked 12 GA

on Quic Disc

™

.

Place the 18 gauge xture wire across the area marked 18 GA on the Quic Disc

™

. After the wires are in place, connect the top of the Quic Disc

™

to the base with supplied screw, making sure that the wires remain at in the bottom portion of the Quic Disc

™

, and the screw is tightened all the

way down.

The copper contacts will automatically pierce the wires’ insulation. Excess 18 GA xture wire that sticks out the end of the Quic Disc

™

is to be cut off.

Make no other wiring connections to the 18 GA xture wire.

B

H

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 15326AZT Center Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 15326AZT Center Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Kichler 15326AZT Center Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Kichler 15821AZT27 Short Lamp

Handleiding

Kichler 15601WHT Surface Lamp

Handleiding

Kichler 15608AZ In Lamp

Handleiding

Kichler 15601BKT Surface Lamp

Handleiding

Kichler 16018AZT30 VLO Lamp

Handleiding

Kichler 15607AZT Surface Lamp

Handleiding

Kichler 16018BKT30 VLO Lamp

Handleiding

Kichler 15439TZT Fundamentals Lamp

Gerelateerde categorieën