Handleiding Kichler 16019AZT27 VLO Lamp

Handleiding

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

IS-16015-US

Date Issued: 07/10/17

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

This fixture is intended for installation in accordance with the National Electric Code (NEC) and Local code

specifications. Failure to adhere to these codes and instructions may result in serious injury and/or property

damage and will void the warranty.

1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool, spa or fountain.

2) According to the requirements of the National Electric Code (NEC), direct burial rated wire is to be buried a

minimum of 6” [152mm] beneath the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M),15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M),15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M),15501-BK; 250’ (76 M), 15502-BK; 500’ (152M),

15505-BK; and 1000’ (304 M), 15506-BK.

3) Wiring connections must be made with approved/listed wire connection device(s) suitable for the application. Do

not exceed manufacturers’ wiring combination specifications for size and quantity of conductors.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO

KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY

DEBRIS THAT HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting fixture.

2) At desired location, hammer stake into ground. To avoid damage to stake, place a board on top of

stake while hammering. If ground is hard and stake is difficult to install, make a crosscut in ground

using a flat shovel.

3) Clear away area in ground at wireway slot in top of stake.

4) Lay 12V cable into wireway slot and screw fixture into stake. Aim fixture in desired direction and

secure by tightening locknut. If necessary, use wrench or pliers for final tightening of nut.

5) Adjust angle of accent light by loosening Phillips head screw.

6) Adjust angle of cowl by loosening thumb screw.

7) TURN OFF POWER.

8) Make wire connections using supplied wire connectors following instructions included, or using

other approved wiring connection method (not supplied).

TO CHANGE LIGHT OUTPUT SETTING:

• NOTE: Fixure switches up in terms of lumen settings; it starts at medium (200 lumens) for the small

accent and starts at low (400 lumens) for the large accent. If these levels are desired, no adjustment

is needed.

• Locate the dimple at the top of the fixture. (This is called a lumen adjustment switch locator)

• Hold magnet on lumen adjustment switch locator for 1.5 seconds to begin programming mode.

Remove magnet.

• Fixture will blink continuously 4x’s at full brightness level and go dark for 2 seconds and then will

illuminate at original factory setting.

• To switch lumen settings, magnet must be reapplied to lumen adjustment switch locator for 1.5

seconds and magnet must be removed for 1 second between switching.

• NOTE: fixture blinks 1x for the lowest lumen setting; 2x’s for the middle lumen setting, and 3x’s for

the highest lumen setting.

• Once the fixture is set and magnet removed, it stays in programming mode for 2 minutes.

• After 2 minutes, the memory is set.

• To change the output brightenss, return to programming mode by holding magnet on magnetic

locator for 1.5 seconds.

• NOTE: Fixture reverts back to original factory setting when put back into programming mode.

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

* DENOTES FACTORY SETTING

PROGRAMMING MODE

LUMEN ADJUSTMENT

SWITCH LOCATOR

SWITCHING

MAGNET

ORIGINAL

PROGRAMMING MODE

LEVEL 1

LEVEL 2

LEVEL 3

WireGauge/Power/LengthChart

10 12 14 16

020 1860/567 1150/351 730/223 450/137

40 930/283 580/177 370/113 230/70

60 620/189 390/119 240/73 150/46

80 470/143 290/88 180/55 110/34

100 370/113 230/70 140/43 90/27

Power(W)

WireGauge/Length(ft/m)

Gen3LumenTableforIS05112017.xlsx

Confidential 1

Level1 Level2 Level3

LumenLevelTable(For2700K/3000K)

SmallAccent

1601516017

LargeAccent

1601816020

100Lm

*400Lm

*200Lm

300Lm

950Lm

650Lm

FixtureLoadChart

9V 12V 15V 9V 12V 15V

Large 3 23 22.5 22.5 18.5 16.5 16

Large 2 16 15.5 15.5 12.5 11 11

Large 1 9 9 9 7 6 6

Small 3 7.5 7.5 8 5.5 5.5 5.5

Small 2 5.5 5.5 5.5 3.5 3.5 3.5

Small 1 3.5 3.5 3.5 2 2 2

Fixture

Style

Lumen

Level

ACVoltage(VA)

DCVoltage(W)

LUMEN ADJUSTMENT

SWITCH LOCATOR

FIXTURE

PHILLIPS HEAD SCREW TO

ADJUST ANGLE OF FIXTURE

THUMB SCREW TO AD-

JUST ANGLE OF COWL

OR TO LOOSEN AND

REMOVE COWL

LOCKNUT

STAKE

WIRE LEADS

SWITCHING

MAGNET

NOTE: When sizing your transformer please use the highest VA you

expect to use depending on desired lumen level to prevent potentially

overloading the transformer.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 16019AZT27 VLO Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 16019AZT27 VLO Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Veelgestelde vragen over Kichler 16019AZT27 VLO Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.