Handleiding Kichler 16024CBR30 VLO Lamp

Handleiding

For warranty information please visit: kichler.com/customer-care/warranty-information/landscape-warranty

IS-16023-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

IMPORTANT! PLEASE READ

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fusebox

before starting and during the installation.

This xture is intended for installation in accordance with the National

Electric Code (NEC) and Local code specications. Failure to adhere to

these codes and instructions may result in serious injury and/or property

damage and will void the warranty. If you are not familiar with code

requirements, installation by a certied electrician is recommended.

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

1) WARNING: This xture is not to be installed within 10 feet (3M) of

a pool, spa or fountain.

2) According to the requirements of the National Electric Code

(NEC), direct burial rated wire is to be buried a minimum of 6”

[152mm] beneath the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local

Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M),15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M),

15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M),

15501-BK; 250’ (76 M), 15502-BK; 500’ (152M), 15505-BK;

and 1000’ (304 M), 15506-BK.

3) Wiring connections must be made with approved/listed wire connection

device(s) suitable for the application. Do not exceed manufacturers’

wiring combination specications for size and quantity of conductors.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE

OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF

POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES,

PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT

HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE

FIXTURE.

INSTALLATION

1) Determine desired location for xture and dig hole. Hole should be

approximately 6” (152mm) in diameter and 10” (254mm) deep.

2) Fill bottom of hole with approximately 3” (76mm) of pea gravel.

3) Lay xture in hole and backll around the xture with soil.

4) Make wire connection to main low voltage supply wire using supplied

twist-on wire connectors following instructions on bag.

BEAM ANGLE ADJUSTMENT

NOTE: Lighting xture comes from the factory with the light module aimed

vertically (straight upward). If beam adjustment is required, follow the

following steps:

• Turn o󰀨 lighting xture before preparing to make beam adjustments.

NOTE: Necessary adjustments need to be made when dark.

• Remove trim ring, glass cover and 8 screws, place hardware in a secure

place. See Figure 1.

• Turn lighting xture on.

NOTE: Light beam direction is accomplished by the gimbal assembly’s

horizontal and vertical adjustability.

• First adjust vertical beam direction using a #2 Phillips screwdriver to pivot

the light module. Place screwdriver in hole provided. See Figure 2.

• Horizontal adjustment is accomplished by placing your hand over light

module and rotating light module left or right. See Figure 2.

• Once beam is adjusted to the desired position, reassemble glass cover

and trim ring using the 8 screws. See Figure 1.

• To ensure proper sealing of unit, replace all 8 screws and hand tighten

screws to where the screw begins to engage with the housing.

• Once all screws are in place, use the numbers on the trim ring and

torque each screw following the torqueing sequence. Tighten each screw

in pattern 20-25 LB-in (2.3 – 2.8 N-m) See Figure 3.

BEAM INTENSITY ADJUSTMENT

NOTE: To adjust beam intensity, see “BEAM INTENSITY ADJUSTMENT”

instructions on PAGE 2.

WIRE GAUGE/POWER/LENGTH INFORMATION

NOTE: For wire gauge/power/length information, see “Wire Gauge/Power/

Length Chart” on PAGE 2.

FIXTURE LOAD INFORMATION

NOTE: For xture load information,see “Fixture Load Chart” on PAGE 2.

SCREW

TRIM RING

Figure 1

SWITCHING

MAGNET

GLASS COVER

1

8

4

6

2

7

3

5

Figure 2

Figure 3

START

LUMEN ADJUSTMENT

SENSOR

SCREWDRIVER

PIVOT HOLE

FOR VERTICAL

ROTATION

LIGHT MODULE

HORIZONTAL

ROTATION

PAGE 1

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired

operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment o󰀨 and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC INFORMATION

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 16024CBR30 VLO Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 16024CBR30 VLO Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Kichler 16024CBR30 VLO Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Kichler 15805BKT27R Shallow Lamp

Handleiding

Kichler 16018CBR27 VLO Lamp

Handleiding

Kichler 16018AZT27 VLO Lamp

Handleiding

Kichler 16016BKT30 VLO Lamp

Handleiding

Kichler 16020CBR27 VLO Lamp

Handleiding

Kichler 15315AZT6 Side Lamp

Handleiding

Kichler 15236BKT Eclipse Lamp

Handleiding

Kichler 16019BKT30 VLO Lamp

Gerelateerde categorieën