Handleiding Kichler 16026AZT30 VLO Lamp

Handleiding

IS-16026-US

* DENOTES FACTORY SETTING

PROGRAMMING MODE

LUMEN ADJUSTMENT

SWITCH LOCATOR

FIXTURE

PHILLIPS HEAD SCREW TO

ADJUST ANGLE OF FIXTURE

LOCKNUT

STAKE

WIRE LEADS

SWITCHING

MAGNET

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

IMPORTANT! PLEASE READ

Lumen Level Table (For 2700K/3000K)

LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4

*150 Lm 300 Lm 450 Lm 600 Lm

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

This xture is intended for installation in accordance with the National Electric Code (NEC) and Local code

specications. Failure to adhere to these codes and instructions may result in serious injury and/or property

damage and will void the warranty. If you are not familiar with code requirements, installation by a certied

electrician is recommended.

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

1) WARNING: This xture is not to be installed within 10 feet (3M) of a pool, spa or fountain.

2) According to the requirements of the National Electric Code (NEC), direct burial rated wire is to be buried a

minimum of 6” [152mm] beneath the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M),15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M),15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M),15501-BK; 250’ (76 M), 15502-BK; 500’ (152M),

15505-BK; and 1000’ (304 M), 15506-BK.

3) Wiring connections must be made with approved/listed wire connection device(s) suitable for the application. Do

not exceed manufacturers’ wiring combination specications for size and quantity of conductors.

4) The unit low voltage cable integral to the product is intended for shallow burial - maximum 6 inches (152 mm).

5) Low voltage cable shall be protected by routing in close proximity to the luminaire, or next to a building structure

such as a house or deck and not be buried except for a maximum of 6 inches (15.2 cm).

6) The unit low voltage cable shall have the length cut off so that it is connected to a connector within 6 inches

(15.2 cm) from a building structure, a luminaire, or tting.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE SHOULD BE

TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES, GRASS CLIPPINGS,

MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting xture.

2) At desired location, hammer stake into ground. To avoid damage to stake, place a board on top of stake while

hammering. If ground is hard and stake is difcult to install, make a crosscut in ground using a at shovel.

3) Clear away area in ground at wireway slot in top of stake.

4) Lay 12V cable into wireway slot and screw xture into stake. Aim xture in desired direction and secure by

tightening locknut. If necessary, use wrench or pliers for nal tightening of nut.

5) Adjust angle of accent light by loosening Phillips head screw.

6) TURN OFF POWER.

7) Make wire connections using supplied wire connectors following instructions included, or using other approved

wiring connection method (not supplied).

TO CHANGE LIGHT OUTPUT SETTING:

• NOTE: Fixture switches up in terms of lumen settings; it starts at “LEVEL 1” (150 lumens). If this level is desired, no

adjustment is needed.

• Locate the dimple at the top of the xture. (This is called a lumen adjustment switch locator)

• Hold magnet on lumen adjustment switch locator for 1.5 seconds to begin programming mode. Remove magnet.

• Fixture will blink continuously 5x’s at full brightness level and go dark for 2 seconds and then will illuminate at

original factory setting (“LEVEL 1”, 150 lumens).

• To switch lumen settings, magnet must be reapplied to lumen adjustment switch locator for 1.5

seconds and magnet must be removed for 1 second between switching.

• NOTE: xture blinks 1x for “LEVEL 1” (150 lumens), 2x’s for “LEVEL 2” (300 lumens), 3x’s for

“LEVEL 3” (450 lumens), 4x’s for “LEVEL 4” (600 lumens).

• Once the xture is set and magnet removed, it stays in programming mode for 2 minutes.

• After 2 minutes, the memory is set.

• To change the output brightness, return to programming mode by holding magnet on magnetic

locator for 1.5 seconds.

• NOTE: Fixture reverts back to original factory setting when put back into programming mode.

• NOTE: Once the desired setting is set, mark the level (1, 2, 3, or 4) with a marker on xture

under the cowl.

For warranty information please visit: kichler.com/warranty

LUMEN

ADJUSTMENT

SWITCH

LOCATOR

SWITCHING

MAGNET

NOTE: When sizing your transformer please use the highest VA you expect to use depending

on desired lumen level per xture to prevent potentially overloading the transformer.

Best practice is to use VA/wattage buffer of 30% when sizing a transformer to account for xture

lumen adjustments. (ie. 210 VA on 300VA transformer.)

WATTS

(VA)

Wire Gauge/Length (ft/m) per run

10 12 14 16

0 - 20 1860/567 1150/351 730/223 450/137

40 930/283 580/177 370/113 230/70

60 620/189 390/119 240/73 150/46

80 470/143 290/88 180/55 110/34

100 370/113 230/70 140/43 90/27

>100 Consult Technical Support

Wire Gauge/Power/Length Chart

Lumen Level VA WATTS

1 3.2 2.0

2 6.0 4.1

3 9.5 6.7

4 13.0 9.4

Fixture Load Chart

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference

that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC INFORMATION

ORIGINAL

PROGRAMMING

MODE

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

REV 3-AUG-2020

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 16026AZT30 VLO Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 16026AZT30 VLO Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Kichler 16026AZT30 VLO Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Kichler 15565BK Transformer Lamp

Handleiding

Kichler 16016CBR30 VLO Lamp

Handleiding

Kichler 16020CBR27 VLO Lamp

Handleiding

Kichler 16019BKT30 VLO Lamp

Handleiding

Kichler 15694AZ Rock Lamp

Handleiding

Kichler 15190BK MR Lamp

Handleiding

Kichler 16018CBR27 VLO Lamp

Handleiding

Kichler 16016WHT30 VLO Lamp

Gerelateerde categorieën