Handleiding Kichler 84313PN Priam Lamp

Handleiding

LIVE (HOT) WIRE (+DC)

FROM FIXTURE (RED or BLACK)

GROUND WIRE FROM

FIXTURE (BARE COPPER)

NEUTRAL WIRE (-DC)

FROM FIXTURE (YELLOW or WHITE)

LIVE (HOT) OUTPUT WIRE

(+DC) FROM DRIVER (RED)

NEUTRAL OUTPUT (-DC)

WIRE FROM DRIVER (YELLOW)

SUPPLY GROUND WIRE

(BARE COPPER OR GREEN)

NEUTRAL INPUT WIRE (-AC)

TO DRIVER (WHITE)

LIVE (HOT) INPUT WIRE (+AC)

TO DRIVER (BLACK)

SUPPLY GROUND WIRE

(BARE COPPER OR GREEN)

SUPPLY NEUTRAL WIRE (WHITE)

CANOPY [D]

DRIVER [J] (ATTACHED

TO CANOPY)

OUTLET

BOX [H]

P4 WIRE NUT

(YELLOW)

P3 WIRE NUT

(ORANGE)

WIRING DIAGRAM

P4 WIRE NUT

(YELLOW)

P3 WIRE NUT

(ORANGE)

P4 WIRE NUT

(YELLOW)

SUPPLY HOT WIRE (BLACK)

Fixture Diagram

Parts List

[A] Stems

[B] Short Threaded

Tubes

[C] Swivel (attached to

canopy)

[D] Canopy

[E] Plate Mounting

Screw

[F] Countersunk

Mounting Screw

[G] Mounting Plate

[H] Outlet Box

[I] Coupling

[J] LED Driver

[K] Decorative Ring

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fusebox before

starng and during the installaon.

WARNING:

This xture is intended for installaon in accordance with the Naonal Electrical

Code (NEC) and all local code specicaons. If you are not familiar with code

requirements, installaon by a cered electrician is recommended.

DIMMING:

This LED xture is compable with most standard incandescent dimmers, LED

dimmers, and electronic low voltage dimmers.

For opmal performance, an electronic low voltage dimmer should be used.

See kichler.com/dimming for a list of compable dimmers.

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a so damp cloth should be used. Harsh cleaning products may damage

the nish.

Installaon Instrucons

1) If desired, rotate top and middle arms up to 45 degrees from linear posion as

shown (Fig.1).

2) Pass xture wires from coupling[I] on top arm through one 12” stem[A]. Screw stem

onto threads protruding from coupling[I].

3) Pass xture wires from 12” stem through one short threaded tube[B]. Screw short

threaded tube into top of 12” stem.

4) Pass xture wires through decorave ring[K] and slip ring over threads protruding

from 12” stem.

5) Pass xture wires from decorave ring through desired number of addional short

threaded tubes[B] and stems[A]. Screw stems together using short threaded tubes.

NOTE: Thread locking compound must be applied to all stem threads as noted with

symbol (4) to prevent accidental rotaon of xture during cleaning, re-lamping, etc.

6) Screw connected stems onto threads protruding through decorave ring[K].

7) Remove mounng plate[G] from canopy[D] by unscrewing three (3) countersunk

mounng screws[F] from canopy. Retain screws for re-aaching canopy to

mounng plate.

8) Pass xture wires from last stem through swivel[C] aached to canopy[D].

9) Screw swivel into end of last stem.

10) Aach mounng plate[G] to outlet box[H] using the plate mounng screws[E].

Mounng plate can be adjusted to suit posion of xture.

11) Cut xture wires a MINIMUM of 6” from top edge of canopy.

NOTE: If the black and white driver lead wires must be trimmed, cut the wires a

MINIMUM of 6” from the top edge of canopy.

12) Wrap supply ground wire (BARE COPPER OR GREEN) around ground screw aached

to mounng plate and ghten screw. Be sure to leave extra wire beyond ground

screw to make connecon with ground wire from xture (no less than 2”).

13) Connect neutral input wire to driver (WHITE) to supply neutral wire (WHITE) using

P4 wire nut (YELLOW).

14) Connect live (HOT) input wire to driver (BLACK) to supply hot wire (BLACK) using P4

wire nut (YELLOW).

15) Connect ground wire from xture (BARE COPPER) to supply ground wire (aached to

the mounng plate ground screw) using a P4 wire nut (YELLOW).

16) Connect neutral wire from xture (YELLOW OR WHITE) to neutral output wire from

driver (YELLOW) using P3 wire nut (ORANGE).

17) Connect live (HOT) wire from xture (RED OR BLACK) to live (HOT) output wire from

driver (RED) using P3 wire nut (ORANGE).

For warranty informaon please visit: kichler.com/warranty

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operaon.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will

not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which

can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Informaon:

REV 28-APR-2021 IS-84313-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

18) Raise xture to ceiling, carefully passing canopy over mounng plate.

NOTE: Be certain wires do not get pinched between plate and canopy or canopy and

ceiling.

19) Align the holes on sides of canopy with holes on anges of mounng plate.

Secure canopy to mounng plate using three (3) countersunk mounng screws[F]

previously removed from canopy.

►

A

B

►

H

E

G

J

F

C

D

I

K

A

B

►

►

OPTIONAL ARM ROTATION :

84313

Fig. 1

OPTIONAL ARM ROTATION

►

A

B

►

H

E

G

J

F

C

D

I

K

A

B

►

►

OPTIONAL ARM ROTATION :

84313

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Kichler 84313PN Priam Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Kichler. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Kichler 84313PN Priam Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Kichler Lampen
Meer handleidingen voor Lampen

Beoordeling

Veelgestelde vragen over Kichler 84313PN Priam Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Kichler 15694AZ Rock Lamp

Handleiding

Kichler 15232AGZ Cross Lamp

Handleiding

Kichler 16016AZT30 VLO Lamp

Handleiding

Kichler 15608AZ In Lamp

Handleiding

Kichler 16016AZT27 VLO Lamp

Handleiding

Kichler 15601BKT Surface Lamp

Handleiding

Kichler 15205BKT Three Lamp

Handleiding

Kichler 10885NILED Ceiling Lamp

Gerelateerde categorieën