Handleiding Logik L16BS11 Blender

Handleiding

GB-1 GB-2 GB-3

UNPACKING

Remove all packaging from the blender. Retain the packaging. If you dispose of it

please do so according to any local regulations.

The following items are included:

• The Main Unit

• Blender Jug (P.N.: HY1101G003)

• Blender Jug Cover (P.N.: HY1101G002)

• Stopper / Measuring Cup (P.N.: HY1101G005)

• Insturction Manual (P.N.: L16BS11-002)

PREPARING AND FILLING THE INGREDIENTS

1. Cut the ingredients into 25mm (1”) cubes before placing them into the blender jug.

If the food is very solid or dry, cut the pieces into smaller cubes.

2. Fill the blender jug with the ingredients.

3. Do not overll the jug. The maximum capacity is 1600 ml, but we suggest you do

not exceed 1250 ml. If you are preparing a large quantity use several smaller

batches.

4. If the ingredients are very dry, put some liquid into the jug. You should never try to

reduce dry ingredients in the blender.

FITTING THE LID

1. Place the lid on the top of the jug and pull the lid.

FITTING THE STOPPER

The stopper has an integral measuring cup

useful for measuring small amounts of

ingredients.

Place the stopper in the slots in the lid and

turn clockwise to lock.

To avoid splashing, always operate the

blender with the stopper rmly in place.

OPERATION

1. Make sure the jug and the lid are secure and in the LOCK position.

2. Set the selector switch to ‘0’.

3. Plug your blender into the mains and switch on the power.

AFTER USE

After you have nished blending:

1. Set the Speed Selector to ‘0’.

2. Hold the jug by the handle and carefully turn it clockwise (towards you) to

release the jug. (This may be easier with one hand on the base and one hand

holding the jug handle).

3. To pour out the contents, rotate the lid of the jug anticlockwise to free it and

then lift off the lid. Pour or spoon the contents out carefully.

4. Unplug the blender from the mains socket.

FIRST TIME USE

1. Before using your blender for the rst time, wash the jug, blade assembly, lid and

stopper. Rinse throughly and dry.

2. Place the base unit on a stable surface, free from heat and moisture and within

easy reach of a mains socket. The mains cable should not be taut.

PRODUCT OVERVIEW

Safety Lid

1

Water Fill Level

2

Speed Selector

3

Base Unit

4

Blade Assembly

7

Stopper/Measuring Cup

5

Handle

6

Mains Cable

8

Do not run the appliance continuously for more than 3 minutes. After a full

3 minute cycle allow the blender to rest for another 5 minutes before

using it again.

• Always operate blender

with cover in place.

FITTING THE JUG TO THE BASE UNIT

Place the jug on the blade assembly as shown.

The jug will t only one way round. If the jug is

not properly tted to the base the blender will

not start.

The lid must be secured to the jug

and the jug to the base otherwise

the blender will not operate!

• Do not run the appliance continuously for more than 3 minutes.

After a full 3 minute cycle allow the blender to rest for another 5

minutes before using it again.

• Never blend very hot liquids in the blender. This is dangerous as the

contents may erupt.

• If you spill liquid on the blender base immediately switch off and

wipe dry

During blending, you can feed in small amounts of food or liquid through the jug

lid. To do this:

1. Hold the lid.

2. Turn the stopper slowly anti-clockwise to free it and then lift it out.

3. Gradually feed pieces of food or liquids into the jug through the feeder.

4. Fit the stopper back when you have nished.

Blender's Operation Modes

• Select the desired operating speed. There are 2

speeds. Move the Speed Selector progressively to

the right to increase the speed. When you start

blending use a low speed to begin with and

gradually increase the speed if necessary.

• To stop the operation, turn the Speed Selector

back to ‘0’.

Use this mode when ingredients need to be

blended in small repeated bursts.

• Turn the Speed Selector to ‘P’ and hold it there for

a short period of time.

• To stop the operation, release the Speed Selector

which will then automatically return to ‘0’.

Continuous (Normal)

operation

Pulsed operation

1

5

6

7

8

2

3

4

If items are missing or damaged, please contact Partmaster (UK only).

Tel: 0844 800 3456 for assistance.

C

M

Y

CM

MY

CY

CMY

K

L16BS11_IB_final110503-running change.pdf 2 04/05/2011 4:27 PM

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Logik L16BS11 Blender. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Logik. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Logik L16BS11 Blender in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Logik Blenders
Meer handleidingen voor Blenders

Veelgestelde vragen over Logik L16BS11 Blender

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Logik L600BK17E Blender

Handleiding

Logik L100BW16E Blender

Handleiding

Logik L600BL15E Blender

Handleiding

Logik L100BR16E Blender

Handleiding

Logik L300SB15E Blender

Handleiding

Logik L16BSS10 Blender

Handleiding

Logik L100BL17E Blender

Handleiding

Logik L15BSS13 Blender

Gerelateerde categorieën