Handleiding Logik L20CTH11 Kachel

Handleiding

Product Overview

Unpacking

Remove all items from the packaging. Retain the packaging. If you dispose of it please do so

according to local regulations.

The following items are included:

Control Panel

Operation

Position the heater upright on the oor away from curtains, furniture or wall coverings before

plugging your heater into the mains socket.

• Connect the heater to the mains socket. Be sure the mains plug ts tightly in mains socket. A

loose t will cause overheating and damage the mains plug.

• Switch the heater on by turning the Power Switch, the power indicator will illuminate red.

• Adjust the Power Switch to set the function,

O mode: The heater is o.

Fan mode: The heating element is o, only the fan is operating.

The heater will blow cool air out from the air outlet.

Low Temp. mode: The heater is in economy mode.

High Temp. mode: The heater is in maximum power.

• To switch the heater o, turn the Power Switch to “O” position. The power indicator will

turn o. Remove the mains plug from mains socket.

Cleaning

Your heater should be cleaned regularly to prevent dirt and dust from building up which will

aect its performance. Ensure the air inlet and the air outlet are not blocked. This can be done

with a vacuum cleaner, using the brush attachment.

Hints & Tips

My heater does not work when I turn it on

• Check that your heater is plugged in and the power is turned on at the mains socket.

• The heater may be overheating. Switch it o and allow it to completely cool down for at

least 30 mins, then switch it on again.

• Turn the Power Switch to the “High Temp” position.

• Try replacing the BSI or ASTS approved 13 Amp BS1362 fuse in the plug.

• If the heater still doesn’t work, do not try to repair the heater yourself.

If your heater’s power is automatically cut o follow the steps

below:

1. Unplug your heater and allow it to cool down for at least 30 mins.

2. Inspect your heater.

3. Plug-in the heater and switch it on again. If it cuts o again, move the heater to a better

ventilated location.

4. If there is any sign of physical damage (e.g. melting, or burning of the case), do not attempt

to use your heater. Please leave all maintenance work to qualied personnel.

Installation

1. Guide the mains cable through the centre of the front base and connect the front base to

the main unit.

2. Fit the rear base onto the front base and the main unit.

3. Screw the four screws through base parts and into the main unit.

4. Attach the power cord guard over the power cord and to the rear

base.

• If items are missing or damaged, please contact Partmaster (UK only).

• Tel: 0344 800 3456 for assistance.

It is normal for the heater to emit some smell and fumes when it is turned on for the

rst time or when turned on after not being used for a long period of time. This smell

will disappear when the heater has been turned on for a short while.

Ensure you unplug your heater from the mains socket and wait for the heater to

cool down completely before cleaning.

The heater cannot be switched on when it is overheating. Allow it to cool down for

at least 30 mins and then switch it on again.

Safety Protective Devices

Overheat Protection System

The power to the heater will automatically cut o if the temperature of the heater exceeds a

certain limit. In the event of overheating, the heater will stop operating. Switch the heater o

and allow it to completely cool for at least 30 mins. The heater will then resume operating as

normal.

Oscillation Function

The heater is equipped with an oscillation feature. If you want to obtain a wider area of heat

circulation, turn the Oscillating Switch to the “On” position. To stop the oscillation, turn the

Oscillating Switch to the “O” position.

Screw x 4

Rear Base x 1

Front Base x 1

The Main Unit

Power Switch Oscillating Switch

Front Rear

Handle

Mains Cable

Rear Base

Front Base

Mains Cable

Slot

Mains Cable

Guard

Specications

Model L20CTH11

Mains supply 220-240V ~50Hz Class II

Power consumption 1900W (High), 1000W (Low), 30W (Fan)

Features and specications are subject to change without prior notice.

Air Inlet

Power Switch

Oscillating Switch

Power

Indicator

Air Outlet

Base

L20CTH11_IB_RC_151201_grace.indd 4-6 1/12/15 2:36 pm

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Logik L20CTH11 Kachel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Logik. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Logik L20CTH11 Kachel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Logik Kachels
Meer handleidingen voor Kachels

Veelgestelde vragen over Logik L20CTH11 Kachel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Logik L20TFH19 Kachel

Handleiding

Logik L20CTH18 Kachel

Handleiding

Logik L20CTH23 Kachel

Handleiding

Logik L18PTC21E Kachel

Handleiding

Logik L20CTH17 Kachel

Handleiding

Logik L15ORW10 Kachel

Handleiding

Logik L15PTC19E Kachel

Handleiding

Logik L15OFR18 Kachel

Gerelateerde categorieën