Handleiding Makita DCS230T Kettingzaag

Handleiding

12

To ensure troublefree operation of the oil pump the oil guide groove at the housing (2) and the oil

inlet bore in the guide bar (3) must be cleaned regularly.

Checking the chain lubrication

Never work with the chain saw without sufficient chain lubrication. Otherwise the service life of the

chain and guide bar will be reduced.

Before starting work check the oil level in the tank and the oil feed.

Check the oil feed rate as described below: Start the chain saw (see “Starting the engine”).

Hold the running chain saw approx. 15 cm above a trunk or the ground (use an appropriate base).

If the lubrication is sufficient, you will see a light oil trace because oil will be flung off the sawing

device. Pay attention to the direction the wind is blowing and avoid unnecessary exposure to the oil

spray!

NOTE:

After the saw has been turned off it is normal for residual chain oil to drip from the oil feed system,

the guide bar and the chain for a time. This does not constitute a defect!

Place the saw on a suitable surface.

Starting the engine

Do not start the saw until it has been completely assembled and inspected!

Move at least 3m away from the place where you fuelled the saw.

Make sure you have a good footing, and place the saw on the ground in such a way that the chain

is not touching anything.

Engage the chain brake (lock).

Grasp the rear handle firmly in one hand and hold the saw firmly against the ground. Press with

one knee on the rear handle.

IMPORTANT: The choke lever (5) is coupled to the throttle lever (1). It will revert to its original posi-

tion automatically once the throttle lever has been pressed.

If the throttle lever is pressed before the engine starts, then the choke switch (5) will have to be

reset to the appropriate position.

Cold start:

Push the short-circuit switch (3) forward.

Turn the choke lever (5) to position . Push primer pump 7 – 10 times.

Slowly pull out the starter cable (4) until you notice resistance (the piston is positioned before the

top dead centre).

Now continue to pull quickly and powerfully. The engine will start after 2 to 4 attempts and will

continue to run (at low temperatures, several starting pulls might be necessary).

CAUTION: Do not pull out the starter cable more than approx. 50 cm, and lead it back by hand. For

efficient starting, it is important to pull the starter cable quickly and powerfully.

As soon as the engine is running smoothly, gently press the throttle lever (1) once (grasp the han-

dle, the safety locking button (2) will release the throttle lever) this will cause the choke lever (5) to

spring back to its original position and the engine will then run at idling speed.

Now release the chain brake.

Warm start:

Proceed as described under cold start, but place the choke lever (5) to position .

Important: If the fuel tank has been completely emptied and the engine has stopped due to lack of

fuel, press the primer pump 7 – 10 times.

Stopping the engine

Put the short-circuiting switch (3) in position “STOP”.

2

3

1

3

2

5

4

Cold start Warm start

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Makita DCS230T Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Makita. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Makita DCS230T Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Makita Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over Makita DCS230T Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Makita DUC355PG2J Kettingzaag

Handleiding

Makita DCS501 Kettingzaag

Handleiding

Makita DUC254Z Kettingzaag

Handleiding

Makita DCS9010 Kettingzaag

Handleiding

Makita UC4001A Kettingzaag

Handleiding

Makita EA6100P Kettingzaag

Handleiding

Makita UC4050A Kettingzaag

Handleiding

Makita BUC122RFEX Kettingzaag

Gerelateerde categorieën