Handleiding Makita HR2810T Boorhamer

Handleiding

8

Chipping/Scaling/Demolition

For models HR2810, HR2810T, HR2811F, HR2811FT

only (Fig. 20)

Set the action mode changing knob to the symbol.

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

Drilling in wood or metal (Fig. 21 – 24)

For Model HR2800, HR28010, HR2810F

Use the optional drill chuck assembly. When installing it,

refer to “Installing or removing the bit” described on the

previous page. Set the action mode changing knob so that

the pointer points to the symbol.

For model HR2810T, HR2811FT

Use the quick change drill chuck as standard equipment.

When installing it, refer to “changing the quick change

chuck for SDS-plus” described on the previous page. Hold

the ring and turn the sleeve counterclockwise to open the

chuck jaws. Place the bit in the chuck as far as it will go.

Hold the ring firmly and turn the sleeve clockwise to

tighten the chuck. To remove the bit, hold the ring and

turn the sleeve counterclockwise. Set the action mode

changing knob to the symbol. You can drill up to 13 mm

diameter in metal and up to 32 mm diameter in wood.

CAUTION:

• Never use “rotation with hammering” when the quick

change drill chuck is installed on the tool. The quick

change drill chuck may be damaged. Also, the drill

chuck will come off when reversing the tool.

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

• There is a tremendous twisting force exerted on the

tool/bit at the time of hole breakthrough. Hold the tool

firmly and exert care when the bit begins to break

through the workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you do

not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

Diamond core drilling

When performing diamond core drilling operations,

always set the change lever to the position to use

“rotation only” action.

CAUTION:

• If performing diamond core drilling operations using

“rotation with hammering” action, the diamond core bit

may be damaged.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• SDS-Plus Carbide-tipped bits

• Bull point

• Core bit

• Cold chisel

• Diamond core bit

• Scaling chisel

• Grooving chisel

• Drill chuck assembly

• Drill chuck S13

• Chuck adapter

• Chuck key S13

• Bit grease

• Side grip

• Depth gauge

• Blow-out bulb

•Dust cup

• Dust extractor attachment

• Safety goggles

• Plastic carrying case

• Keyless drill chuck

For Model HR2800

Noise

ENG102-3

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA

): 89 dB (A)

Sound power level (L

WA

): 100 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG217-2

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: hammer drilling into concrete

Vibration emission (a

h,HD

): 20.0 m/s

2

Uncertainty (K): 1.5 m/s

2

ENG302-2

Work mode: drilling into metal

Vibration emission (a

h,D

): 2.5 m/s

2

or less

Uncertainty (K): 1.5 m/s

2

For Model HR2810, HR2810T

Noise

ENG102-3

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA

): 89 dB (A)

Sound power level (L

WA

): 100 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Makita HR2810T Boorhamer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Makita. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Makita HR2810T Boorhamer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Makita Boorhamers
Meer handleidingen voor Boorhamers

Veelgestelde vragen over Makita HR2810T Boorhamer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Makita HR2440X Boorhamer

Handleiding

Makita HR2441 Boorhamer

Handleiding

Makita HR2420 Boorhamer

Handleiding

Makita BHR200 Boorhamer

Handleiding

Makita BHR242 Boorhamer

Handleiding

Makita HR2631FT Boorhamer

Handleiding

Makita DHR202 Boorhamer

Handleiding

Makita HR262D Boorhamer

Gerelateerde categorieën