Handleiding McCulloch EB356a Kettingzaag

Handleiding

10 11

4 - FUEL AND LUBRICATION

4-1. FUEL

Use regular g

rade unleaded gasoline mixed with Genuine

Factory Parts 40:1 custom 2-cycle engine oil for best

results. Use mixing ratios in Section 4-3.

Never use straight gasoline in your unit.This will cause

permanent engine damage and void the manufactur-

er’s warranty for that product. Never use a fuel mixture that

has been stored for over 90 days.

If 2-cycle lubricant other than Genuine Factory Parts

Custom Lubricant is to be used, it must be a premium

grade oil for 2-cycle air cooled engines mixed at a 40:1

ratio. Do not use any 2-cycle oil product with a recommend-

ed mixing ratio of 100:1. If insufficient lubrication is the

cause of engine damage, it voids the manufacturer’s

engine warranty for that occurrence.

4-2. MIXING FUEL

Mix fuel with Genuine Factory Parts brand 2 cycle oil in an

approved container. Use mixing table for correct ratio of fuel

to oil. Shake container to ensure thorough mix.

Lack of lubrication voids engine warranty.

4-3.FUEL AND LUBRICATION SYMBOLS

FUEL MIXING TABLE

4-4.RECOMMENDED FUELS

Some conventional gasolines are being blended with oxy-

genates such as alcohol or an ether compound to meet

clean air standards. Your McCulloch engine is designed to

operate on any gasoline intended for automotive use

including oxygenated gasolines.

4-5.CHAIN AND BAR LUBRICATION

Always refill the chain oil tank each time the fuel tank is

refilled. We recommend using Genuine Factory Parts

Chain, Bar and Sprocket Oil, which contains additives to

reduce friction and wear and to assist in the prevention of

pitch formation on the bar and chain.

Gasoline and Oil

Mix 40:1

Oil Only

5 - OPERATING INSTRUCTIONS

5-1. ENGINE PRE-START CHECKS

WARNING

Never start or operate the saw unless the bar and chain are

properly installed.

1. Fill the fuel tank (A) with correct fuel mixture (Figure

5-1A).

2. Fill the oil tank (B) with correct chain and bar oil

(Figure 5-1A).

3. Be certain the CHAIN BRAKE

®

is disengaged (C)

before starting unit (Figure 5-1A).

NOTE: See page 9 Fig. 3-5A & 3-5B.

5-2. TO START ENGINE

1. Press red STOP switch to the “I” ON position (Fig. 5-

2A).

2. Pull out the choke (A) to the point where it latches in

place. (Fig. 5-2B)

3. Push the primer bulb (B) 10 times. (Fig. 5-2C)

4. Latch throttle advance: depress latch and hold (C)

squeeze throttle trigger (D) release trigger and then

the latch. (Fig. 5-2D)

5. Place the saw on a firm and level surface. Hold the

sa

w securely with y

our f

oot as illustr

ated. Pull sharply

on the starter 4 times. Watch the chain in case it runs.

(Fig. 5-2E)

NOTE: If the engine sounds as if it wants to start before the

4th pull, end the tugging of the starter and proceed as

described in the next step.

6. Push in the choke (E) as far it will go. (Fig. 5-2F)

7.

Hold the sa

w securely and tug shar

ply on the star

ter

4 times. The engine should start.

8.

Let the engine r

un f

or 10 seconds to w

arm up. Press

the tr

igger (F) and put it into idle

.

(Fig.

5-2G)

9. If the engine does not start up, repeat the above

steps

.

IMPORTANT IDLING INFORMATION

In some cases due to operating conditions (altitude, tem-

perature etc.) your chain saw may need a slight adjustment

to the idle speed.

After w

ar

m up - See the User's Manual section 5-2, step 7

- If unit does not Idle after restar

ting 2 times

, f

ollo

w these

steps to adjust idle.

1. Idle adjustment access (G). (Figure 5-2H)

2. Using a Phillips or slotted screwdriver - turn screw 1/4

to 1/2 turn clockwise (to the right). Unit should then

idle properly. (Figure 5-2H)

NOTE: If chain turns while idling - turn screw back to the

left until chain stops and unit continues to idle.

5-1A

C

A

B

5-2A

5-2B

A

5-2C

B

5-2D

5-2E

C

D

5-2F 5-2G

E

F

5-2H 5-2H

G

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je McCulloch EB356a Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met McCulloch. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van McCulloch EB356a Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor McCulloch Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over McCulloch EB356a Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

McCulloch MXC1640DK Kettingzaag

Handleiding

McCulloch CSE 2040S Kettingzaag

Handleiding

McCulloch M4218 Kettingzaag

Handleiding

McCulloch CS 360T Kettingzaag

Handleiding

McCulloch Mac 540E Kettingzaag

Handleiding

McCulloch MCC3516F Kettingzaag

Handleiding

McCulloch CS 410 Elite Kettingzaag

Handleiding

McCulloch MXC1640D Kettingzaag

Gerelateerde categorieën