Handleiding McCulloch EB356a Kettingzaag

Handleiding

7-2. AIR FILTER

CAUTION

Ne

ver operate saw without the air filter. Dust and dirt will be

drawn into engine and damage it. Keep the air filter clean!

TO CLEAN AIR FILTER:

1. Remove knob (A) holding air filter cover in place,

remove the top cover (B) by loosening the cover

retaining screws. Cover will lift off.(Figure 7-2A)

2. Completely remove the air filter box (B) from the unit.

(Figure 7-2B)

3. Clean air filter box by using air cleaner or brush.

NOTE: Never clean air filter with liquid material or it may

cause air filter damaged.

4. Install air filter. Install engine / air filter cover. Make

sure latche (E) latch (F) and cover fit properly. Tighten

the cover retaining knob securely. (Figure 7-2C &

Figure 7-2D)

WARNING

Never perform maintenance when the engine is hot, to

avoid any chance of burning hands or fingers.

7-3.FUEL FILTER

CAUTION

Ne

v

er oper

ate y

our sa

w without a fuel filter

.

The fuel filter

should be replaced after each 20 hours of use. Drain fuel

tank completely bef

ore changing filter

.

1. Completely remove the fuel cap from the gas tank.

2.

Bend a piece of soft wire to f

or

m a hook at the end.

3. Reach into fuel tank opening and hook fuel line.

Carefully pull the fuel line toward the opening until you

can reach it with y

our fingers.

NOTE: Do not pull hose completely out of tank.

4. Lift filter (A) out of tank (Figure 7-3A).

5. Pull filter off with a twisting motion. Discard filter.

6. Install new filter. Insert end of filter into tank opening.

Make sure filter sits in bottom corner of tank. Use a

long handle screwdriver to aid in filter placement if

necessary.

7. Fill tank with fresh fuel / oil mixture. See Section 4,

Fuel and Lubrication. Install fuel cap.

7-4. SPARK ARRESTER SCREEN (Figure 7-

4A)

NOTE: A clogged spark arrester screen will dramatically

reduce engine performance.

1. Remove the 2 nuts (A) and pull muffler out. (Figure7-

4A).

2. Remove the 1 screw (B) that holds the spark arrester

cover (C) . (Figure 7-4B)

3. Discard the used spark arrester screen (D) and

replace it with a new one.

4. Reasemble the muffler components and install the

muffler to the cylinder. Tighten securely.

16 17

7 - MAINTENANCE INSTRUCTIONS

7-4B

A

B

C

D

7-2A

7-2B

B

7-3A

B

A

C

7-2C 7-2D

B

E

F

D

F

7-3A

A

B

7-5. SPARK PLUG

NOTE: For efficient operation of saw engine, spark plug

must be kept clean and properly gapped.

1. Push STOP switch down.

2. Remove air cleaner cover.

3. Disconnect the wire connector (G) from the spark plug

(H) by pulling and twisting at the same time (Figure 7-

5A).

4. Remove spark plug with spark plug socket wrench.

DO NOT USE ANY OTHER TOOL.

5. Check electtrode gaps with wire feeler gauge and set

gaps to .025” (.635mm) if necessary.

6. Reinstall a new spark plug.

NOTE: A resistor spark plug must be used for replacement

(Part no. 9295-310801).

NOTE: This spark ignition system meets all requirements

of the Canadian Interference-Causing Equipment

Regulations.

7-6.CARBURETOR ADJUSTMENT

The carburetor was pre-set at the factory for optimum per-

f

ormance. If further adjustments are necessary, please take

your unit to the nearest Authorized Service Center listed in

the Yellow Pages.

7-7.STORING A CHAIN SAW

CAUTION

Never store a chain saw for longer than 30 days without

performing the following procedures.

Storing a chain saw for longer than 30 days requires stor-

age maintenance. Unless the storage instructions are fol-

lowed, fuel remaining in the carburetor will evaporate, leav-

ing gum-like deposits. This could lead to difficult starting

and result in costly repairs.

1.

Remo

v

e the fuel tank cap slo

wly to release an

y pres

-

sure in tank. Carefully drain the fuel tank.

2. Start the engine and let it run until the unit stops to

remo

ve fuel from carburetor.

3. Allow the engine to cool (approx. 5 minutes).

4. Using a spark plug wrench, remove the spark plug.

5. Pour 1 teaspoon of clean 2-cycle oil into the combus-

tion chamber. Pull starter rope slowly several times to

coat internal components. Replace spark plug (Figure

7-7A).

NOTE: Store the unit in a dry place and away from possi-

ble sources of ignition such as a furnace, gas hot water

heater, gas dryer, etc.

7-8.REMOVING A UNIT FROM STORAGE

1. Remove spark plug.

2. Pull starter rope briskly to clear excess oil from com-

bustion chamber.

3. Clean and gap spark plug or install a new spark plug

with proper gap.

4. Prepare unit for operation.

5. Fill fuel tank with proper fuel / oil mixture. See Fuel

and Lubrication Section.

7 - MAINTENANCE INSTRUCTIONS

7-5A

H

G

7-7A

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je McCulloch EB356a Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met McCulloch. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van McCulloch EB356a Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor McCulloch Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over McCulloch EB356a Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

McCulloch MXC1640DK Kettingzaag

Handleiding

McCulloch CSE 2040S Kettingzaag

Handleiding

McCulloch M4218 Kettingzaag

Handleiding

McCulloch CS 360T Kettingzaag

Handleiding

McCulloch Mac 540E Kettingzaag

Handleiding

McCulloch MCC3516F Kettingzaag

Handleiding

McCulloch CS 410 Elite Kettingzaag

Handleiding

McCulloch MXC1640D Kettingzaag

Gerelateerde categorieën