Handleiding Milwaukee 2565-20 Slagmoersleutel

Handleiding

4

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow the

motor to come to a complete stop before using the

control switch.

PUSH TO CENTER TO LOCK

Push for

reverse

Push for

forward

1. For forward (clockwise) rotation, push the control

switch in the direction shown. Check the direction

of rotation before use.

2. For reverse (counterclockwise) rotation, push the

control switch in the direction shown. Check the

direction of rotation before use.

3. To lock the trigger, push the control switch to the

center position. The trigger will not work when the

control switch is in the locked position.

Always remove the battery pack before performing

maintenance, changing accessories, storing the tool

and any time the tool is not in use.

Using the Drive Control

The drive control button is used to

Drive Control

adjust the rotation speed (RPM)

for the application.

To select the drive control mode:

1. Unlock, then pull and release

the trigger to turn on the tool.

The current indicator is lit.

NOTE: The trigger will not work

when the control switch is in the

locked position.

2. Press the drive control but-

ton to cycle through the 4

modes. When the desired mode indicator is lit,

begin work.

3. In mode:

Mode RPM IPM

1 0-1550 0-1350

2 0-2300 0-2700

3 0-3000 0-3600

0-3000* 0-3600*

• Auto Shut Off - In

forward, the tool runs at

a reduced RPM and then

shuts o󰀨 once the torque

is achieved.

• Bolt Removal - In

reverse, the tool runs at

full RPM and IPM until

the nut breaks free from

the joint. Then, the tool slows to a reduced RPM

for better control in removing the nut.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from 0

to full speed.

1. To start the tool, pull the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the driving speed, simply increase or

decrease pressure on the trigger. The further the

trigger is pulled, the greater the speed.

3. To stop the tool, release the trigger and the electric

brake stops the tool instantly.

ASSEMBLY

WARNING

Recharge only with the charger

specied for the battery. For spe-

cic charging instructions, read the operator’s

manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

WARNING

Always remove battery pack before

changing or removing accessories.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

WARNING

Only use accessories specically

recommended for this tool. Others

may be hazardous.

Attaching and Removing Accessories

3/8" and 1/2" Friction Ring

(Cat. No. 2564-20 and 2565-20)

1. Use only the appropriate size Square Drive Sockets.

2. To attach a socket, align the accessory with the

anvil and push it rmly over the retaining ring.

3. To remove the accessory, pull the accessory o󰀨

the anvil.

1/2" Pin Detent

(Cat. No. 2565P-20)

1. Use only the appropriate size Square Drive

Sockets.

2. To attach a socket, align the hole in the accessory

with the detent pin on the anvil. Hold the detent

pin in while pushing the socket onto the anvil.

The detent pin will snap into place in the hole to

secure the socket.

3. To remove the socket, insert a nail or other thin

object into the hole in the accessory and press

in the detent pin. Pull the accessory o󰀨 the anvil.

OPERATION

WARNING

To reduce the risk of injury, always

wear proper eye protection marked

to comply with ANSI Z87.1.

When working in dusty situations, wear appro-

priate respiratory protection or use an OSHA

compliant dust extraction solution.

Fuel Gauge

To determine the amount of charge left in the battery,

turn the tool ON. The Fuel Gauge will light up for 2-3

seconds. When less than 10% of charge is left, 1 light

on the fuel gauge will ash 4 times.

To signal the end of charge, 1 light on the fuel gauge

will ash 8 times and the tool will not run. Charge

the battery pack.

If the battery becomes too hot, the fuel gauge lights

will ash in an alternating pattern and the tool will not

run. Allow the battery to cool down.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Milwaukee 2565-20 Slagmoersleutel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Milwaukee. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Milwaukee 2565-20 Slagmoersleutel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Milwaukee Slagmoersleutels
Meer handleidingen voor Slagmoersleutels

Veelgestelde vragen over Milwaukee 2565-20 Slagmoersleutel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Milwaukee 2555P-20 Slagmoersleutel

Handleiding

Milwaukee 2754-20 Slagmoersleutel

Handleiding

Milwaukee 2758-22 Slagmoersleutel

Handleiding

Milwaukee 2962-22R Slagmoersleutel

Handleiding

Milwaukee 2860-20 Slagmoersleutel

Handleiding

Milwaukee 2753-20 Slagmoersleutel

Handleiding

Milwaukee 2665-20 Slagmoersleutel

Handleiding

Milwaukee 2762-20 Slagmoersleutel

Gerelateerde categorieën