Handleiding Milwaukee 2663-22 Slagmoersleutel

Handleiding

4

OPERATION

WARNING

To reduce the risk of injury, always

wear proper eye protection marked

to comply with ANSI Z87.1.

When working in dusty situations, wear appro-

priate respiratory protection or use an OSHA

compliant dust extraction solution.

Always remove battery pack before changing

or removing accessories. Only use accessories

specically recommended for this tool. Others

may be hazardous.

Keep hands away from all moving parts.

Using Control Switch

The control switch may be set to three positions: for-

ward, reverse and lock. Due to a lockout mechanism,

the control switch can only be adjusted when the trig-

ger is not pressed. Always allow the motor to come

to a complete stop before using the control switch.

1. For forward (clockwise) rotation, push the control

switch from the right side of the tool. Check the

direction of rotation before use.

2. For reverse (counterclockwise) rotation, push the

control switch from the left side of the tool. Check

the direction of rotation before use.

3. To lock the trigger, push the control switch to the

center position. The trigger will not work when the

control switch is in the locked position.

Always remove the battery pack before performing

maintenance or changing accessories. Always

lock the trigger or remove the battery pack before

storing the tool and any time the tool is not in use.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from 0

to full speed.

1. To start the tool, grasp the handle rmly and pull

the trigger.

2. To vary the driving speed, increase or decrease

pressure on the trigger. The further the trigger is

pulled, the greater the speed.

3. To stop the tool, release the trigger. Ensure the

tool has come to a complete stop before laying

the tool down.

Impacting Techniques

The longer a bolt, screw, or nut is impacted, the

tighter it will become. To help prevent damaging the

fasteners or workpieces, avoid excessive impact-

ing. Be particularly careful when impacting smaller

fasteners because they require less impacting to

reach optimum torque.

Practice with various fasteners, noting the length of

time required to reach the desired torque. Check the

tightness with a hand-torque wrench. If the fasteners

are too tight, reduce the impacting time. If they are not

tight enough, increase the impacting time.

Oil, dirt, rust or other matter on the threads or under the

head of the fastener a󰀨ects the degree of tightness.

The torque required to loosen a fastener averages

75% to 80% of the tightening torque, depending on

the condition of the contacting surfaces.

On light gasket jobs, run each fastener down to a

relatively light torque and use a hand torque wrench

for nal tightening.

ASSEMBLY

WARNING

Recharge only with the charger

specied for the battery. For spe-

cic charging instructions, read the operator’s

manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

WARNING

Always lock the trigger or remove

the battery pack any time the tool

is not in use.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

WARNING

Only use accessories specically

recommended for this tool. Others

may be hazardous.

Attaching and Removing the Tool Hanger

1. To attach, remove the two top gear case screws.

2. Place the ring through the tool hanger.

3. Position the tool hanger on the tool over the two

gear case screw holes.

4 Replace the two gear case screws. Hand tighten

the screws.

5. To remove, reverse the procedure.

WARNING

Use only sockets and other acces-

sories specifically designed for

use on impact wrenches and drivers. Other

sockets and accessories might shatter or break

causing injury.

Attaching and Removing Accessories

These tools are intended only for use with accesso-

ries designed for impact wrenches and drivers.Other

sockets could shatter or break, causing injury.

Cat. No. 2662-20

1. Use only the appropriate size Square

Drive Sockets.

2. To attach a socket, align the hole in

the accessory with the detent pin on

the drive shank. Hold the detent pin

in while pushing the socket onto the

drive shank. The detent pin will snap

into place in the hole to secure the

socket.

3. To remove the socket, insert a nail or

other thin object into the hole in the

accessory and press in the detent pin.

Pull the accessory o󰀨 the drive shank.

Cat. No. 2663-20, 2664-20

1. Use only the appropriate size Square Drive Sock-

ets.

2. To attach a socket, align the accessory with the

drive shank and push it rmly over the retaining

ring.

3. To remove the accessory, pull the accessory o󰀨

the drive shank.

Cat. No. 2665-20

This driver is intended for use with drill and driver

bits with a 7/16" hex shank and ball detent recess.

1. To attach an accessory, pull the ring out and insert

the accessory shank. Release the ring. It may be

necessary to pull the bit out slightly to engage the

holding mechanism.

2. To remove the accessory, pull out the ring and

remove the accessory. Release the ring.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Milwaukee 2663-22 Slagmoersleutel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Milwaukee. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Milwaukee 2663-22 Slagmoersleutel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Milwaukee Slagmoersleutels
Meer handleidingen voor Slagmoersleutels

Veelgestelde vragen over Milwaukee 2663-22 Slagmoersleutel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Milwaukee 9070-20 Slagmoersleutel

Handleiding

Milwaukee 2664-22 Slagmoersleutel

Handleiding

Milwaukee 2762-20 Slagmoersleutel

Handleiding

Milwaukee 2862-20 Slagmoersleutel

Handleiding

Milwaukee 2862-22 Slagmoersleutel

Handleiding

Milwaukee 2452-22 Slagmoersleutel

Handleiding

Milwaukee 2753-20 Slagmoersleutel

Handleiding

Milwaukee 2967-22GG Slagmoersleutel

Gerelateerde categorieën