Handleiding Nissin Di866 Professional (for Canon) Flitser

Handleiding

x 4

NOTE

BASIC OPERATION

SETTING THE MODE AND THE FUNCTION

Remove the battery magazine and insert

4 x size AA batteries as shown in the

picture.

Press the on/off switch. Screen A appears, and the mode A is set.

The pilot lamp blinks red showing the unit is charging.

In a few seconds, the pilot lamp turns green.

The display screen automatically turns off in about 30sec. after the setting

job is terminated.

For a test-flash, press the pilot lamp.

To turn off the flash unit manually, press the on/off switch and hold it for 2

seconds.

Set Di866 to the camera’s hotshoe and press the on/off switch to power on.

Display screen automatically shows A, the Full Automatic

Mode.

Di866 is now set for the camera’s automatic flash control

system.

Press the on/off switch once again to lock this condition on

your flash. (Press it again to release the lock)

All the jobs required for this mode is completed.

When the pilot lamp turns green, press the shutter button of your camera

halfway to focus the subject.

Shutter speed, aperture and flash mark ( ) are shown in camera’s view finder

and the display panel of the camera.

Press the shutter, and Di866 is fired. The result is immediately shown on the

camera’s LCD monitor.

Flash power is automatically controlled by the camera and the most proper

exposure is obtained on your picture.

When you change the focal length of your camera lens, Di866 responds without

delay and set its light source for the proper illumination angle.

The battery compartment is specially

designed so that every cell is placed in the

same direction to avoid the confusion in

poor light condition.

It is recommended to use all 4 batteries in same brand and type, and

replace them all at the same time.

Wrong insertion of each cell would not make electric contact.

+/- symbol is clearly marked at the battery

compartment.

Place the battery magazine back into the

body.

7 8

9

10

!

1.

2.

The power is automatically turned off (to stand-by mode), in about 30 sec.

of idle use on the camera or after the last setting job. To save the battery

energy, you can select the display-off setting from the custom setting. In

this case, the display screen turns off in about 8 sec. of idle use.

While Di866 is in the stand-by mode, display screen turns off and the pilot

lamp blinks every 2 seconds showing the flash unit is in stand-by mode.

To turn on Di866 again, press the camera’s shutter button halfway or

press any button of the flash unit.

In case Di866 is not in use over 30 minutes, the unit is completely turned

off and shut out the current leakage from the batteries.

To turn on Di866 again, take the first step of turning the flash unit on.

In case of using Di866 in off-camera-use mode (Wireless TTL flash-slave,

Universal Slave function), it is recommended to change the turn off timer

at the Custom setting....ref. page 32 .

The mode and the value set on the flash unit before turning off is

memorized and returns in the same condition when switch it on again.

1.

2.

4.

When the recycle time becomes longer

than 20 sec., replace the batteries with the

fresh ones or recharge the batteries

(rechargeable batteries).

3.

Turn off the power switch of both Di866

and the camera

Turn the lock ring of Di866 to loosen it all

the way as shown in the picture.

Slide the mounting foot of Di866 into the

hotshoe of the camera.

Turn the lock ring to opposite direction

and tighten it.

1.

2.

3.

4.

Lock pin comes out to hook the foot at the

hotshoe for sure contact.

5.

Loosen the lock ring and slide the mounting foot of Di866 off the hotshoe of

the camera. Make sure to turn the lock ring all the way to completely clear

the lock pin off the hooking slot on the hotshoe.

Inserting batteries

Turn on the flash unit

Mounting Di866 on the Camera

Removing Di866 from the Camera

Di866 has energy saving double power off function.

Full Automatic Flash Control

Usable batteries - Alkaline batteries, Lithium batteries, NiMH batteries.

The modes to be set on the camera:

In all those camera’s modes listed above, Di866 will automatically

and fully work in ETTL automatic flash control system.

(Full Auto), (Program), (Shutter priority),

Portrait, Landscape, Close-up, Sports,

Tv

Av

A-DEP

Night Portrait.

(Aperture priority), (Manual), Automatic depth-of-field,

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Nissin Di866 Professional (for Canon) Flitser. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Nissin. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Nissin Di866 Professional (for Canon) Flitser in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Nissin Flitsers
Meer handleidingen voor Flitsers

Beoordeling

Veelgestelde vragen over Nissin Di866 Professional (for Canon) Flitser

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Nissin Di866 mark II (for Nikon) Flitser

Handleiding

Nissin MG8000 Extreme (for Nikon) Flitser

Handleiding

Nissin Di700A (for Sony) Flitser

Handleiding

Nissin Di466 FT Flitser

Handleiding

Nissin Di700 (for Canon and Nikon) Flitser

Handleiding

Nissin i600 Flitser

Handleiding

Nissin i60A (for Sony) Flitser

Handleiding

Nissin Di28 Flitser

Gerelateerde categorieën