Handleiding One For All URC 7880 Afstandsbediening

Handleiding

Your One For All remote control can learn any function from any other working remote

control. This can be useful if you are missing one or more functions from your original

remote control and would like to add them to the Smart Control. You can learn onto any

key except Magic, Devices or Activity.

You can also learn a complete device if you can’t fi nd a code.

To learn, fi rstly make sure you have all your original remote controls to hand, and that they

have working batteries in. To learn functions, the original remote should be

approximately 3cm from the OFA remote, pointing towards it as shown below:

1. Hold down MAGIC until the LED under the device blinks twice. The LED

under the current mode key will stay lit.

2. Using the DEVICES key, make sure the LED for the device you want to learn

functions on is lit.

3. Press 975 – the LED will blink twice.

4. Press and release the key you want to learn a function onto (for example

the A key) – The Watch TV, Listen To Music and Custom LEDs will light up.

5. Press and release the key on the original remote.

6. The LED will blink twice to indicate the key has been learned correctly.

7. Repeat steps 4 and 5 for each key you want to learn – remember you can learn from multiple

remotes, but only one function per key.

8. When you learned all the functions you require, press and hold the MAGIC

key until the LED blinks twice and turns off .

Hints

• If the LEDs shows one long blink at step 6, the function was not learned correctly, please try again

from step 4.

• If you fi nd one or more keys don’t work properly after set up, you can re-enter the learning mode

at any time by repeating the procedure from step 1.

If you always use one device to control volume, for example your TV or an AV Receiver, you

can set up the Smart Control to always control that device, regardless of which device your

remote is controlling.

To do this:

1. Hold down MAGIC until the LED under the device blinks twice. The LED under the

current mode key will stay lit.

2. Press 993 – the LED will blink twice.

3. Use the DEVICES key to select the Device you want to lock the Volume to.

4. Press MAGIC once – the LED will blink twice and volume is now locked.

If there is one particular device you would like to exclude from the Volume Lock (and

control its own volume), you can do this by the following:

1. Hold down MAGIC until the LED under the device blinks twice. The LED under the

current mode key will stay lit.

2. Press 993 – the LED will blink twice.

3. Use the DEVICES key to select the Device you remove from Volume Lock.

4. Press VOLUME DOWN – the LED will blink four times and device is now removed.

To unlock the volume and set every device back to controlling its own volume, the

procedure is:

1. Hold down MAGIC until the LED under the device blinks twice.

The LED under the current mode key will stay lit.

2. Press 993 – the LED will blink twice.

3. Press VOLUME UP – the LED will blink four times and Volume is now unlocked.

Please note that Volume Lock only applies in Device Mode – Activities are unaff ected.

PROGRAM A MACRO

You can program any key on your OFA remote (except MAGIC, DEVICES and the three App

Shortcut keys) to send multiple commands on a single press –a Macro. This can be useful

for controlling multiple devices to put them in a certain state – for instance you could put

your TV on HDMI 1 and press Play on the Blu-ray player to start watching a movie. A key

programmed with a Macro will send the same Macro regardless of the device mode, so it

is best to select a key you don’t use, or use one of the spare A, B or C keys.

To program a macro, the procedure is as follows:

1. Hold down MAGIC until the LED under the device blinks twice.

The LED under the current mode key will stay lit.

2. Press 995 – the LED will blink twice.

3. Next select the key you want to program the Macro on.

4. Now use the DEVICES key to select the device you want the fi rst

function of the Macro to come from, for example TV.

5. Next, press the key you want to include in the Macro, for example

the INPUT key.

6. Repeat steps 4 (if necessary), and 5 to add more keys to the Macro. You can include up

to 15 key presses.

7. To store the Macro, hold down the MAGIC key until the LED blinks

twice.

* Remember to press the keys in the same order you would using your original remotes – so if you pressed AV on the TV

remote and then Play on the Blu-ray remote to watch a movie, do it in the same order on the Smart Control.

* If the LED shows a long blink when you press a key in steps 3 or 4, you have entered too many keys, please try again.

TO DELETE A MACRO

If you want to remove a macro from a key, please perform the following:

1. Hold down MAGIC until the LED under the device blinks twice.

The LED under the current mode key will stay lit.

2. Press 995 – the LED will blink twice.

3. Press the key the macro is programmed on.

4. Now hold down the MAGIC key until the LED blinks twice –

the Macro is deleted.

MACROS ON ACTIVITIES

Another handy feature of the Smart Control is to put Macros on Activities; you could for

example program the Watch TV Activity to send a Macro to turn on the TV and Set Top

Box when selected. To do this, simply use the Activity key to select the Activity in step 3 of

the procedure “Program a Macro”. Next time you use the Activity, the Macro will be sent 3

seconds after you select it using the Activity key.

If you want to delete a Macro from the Activity, select it during step 3 of “To Delete a

Macro”.

LEARNING MACROS MACROS

VOLUME LOCK

The Smart Control features 3 App Shortcut keys for viewing digital TV, streamed over the

internet. If your original remote control already had a key for this - for example many newer

TVs have a Netfl ix key - then this key will perform exactly the same as the key on your

original remote. However if you did not have a key like this, but still had the ability to watch

a streaming service, you can use this key as a shortcut by programming a macro on it. Most

AV devices which are connected to the internet, such as Smart TVs or streaming Set Top

Boxes have one or more applications they can run to access TV viewing via the internet.

Examples of these would be Netfl ix, YouTube, Amazon Prime, BBC iPlayer or similar.

To program the macro, you fi rst need to know the device you use to access the service, and

then the sequence of keys you need to press to always bring up the service you prefer, For

example, some Panasonic TVs will start Netfl ix by pressing the Apps key, then Menu Down

Twice, and fi nally the OK key. Or on an Apple TV, the sequence is Menu, Menu Down and OK.

Once you have determined the sequence for your device, follow these steps:

1. Sit in front of your device with It switched on (not on standby)

2.

Hold down the App Shortcut key until the LED blinks twice and stays lit

3. Use the DEVICES key to select the device you want to use for the

App Shortcut

macro (e.g. TV)

4. Now perform the sequence of keys exactly as would normally.

The remote will operate your device and the macro is recorded in

real time - so if it normally takes a few seconds for your device to

react don’t worry.

5. One you have fi nished the sequence - and the Streaming Service

has started on your device - hold down the

App Shortcut

key until

the LED blinks twice and goes out. The macro is now stored.

Tips

• Make sure the Smart Control Is operating the device in question before programming

• If you fi nd the Macro doesn’t work as expected, you can just repeat the same

sequence to reprogram

• When programming, wait for your device to respond fi rst, the remote will remember

the timing

• The

App Shortcut

macro is tied to one device, remember to make sure you are

watching the correct device.

APP SHORTCUT FEATURE

Customer Support: 855-716-2573 (toll free)

OFA warranty/terms & conditions: 855-569-6595 (toll free)

www.oneforall.com

Imported into the US by:

Universal Electronics Inc.

UEI Technical Support Services,

Suite 301

26250 Euclid Ave.

Euclid, OH 44132

One For All is a registered trademark of UEI

Made in China, Hecho en China

711753

RDN 1250618

2 - 5 CM

GUIDE

2 - 5 CM

GUIDE

INPUT

INPUT

2 - 5 CM

GUIDE

INPUT

2 - 5 CM

GUIDE

INPUT

2 - 5 CM

GUIDE

INPUT

An Activity is a grouping of two or more devices into a single mode based upon what

you’re doing while using your remote - for example TV and Set Top Box can be combined

together into a Watch TV mode. In this mode keys will control only the relevant device, so

in this example the Volume keys would control the TV, but the channel keys would control

the Set Top Box.

The OFA Smart Control features 5 Activity Modes; Watch TV, Watch Movie, Listen To Music,

Play Game and Custom. Each of these modes has a choice of devices to combine.

These are:

WATCH TV

Combination 1: TV + STB (Default)

Combination 2: TV + STB + AUD

Combination 3: TV + AUD

Combination 4: TV + S.BAR

Combination 5: TV + STB + S.BAR

WATCH MOVIE

Combination 1: TV + BLU (Default)

Combination 2: TV + BLU + AUD

Combination 3: TV + DVD

Combination 4: TV + DVD + AUD

Combination 5: TV + BLU + S.BAR

Combination 6: TV + DVD + S.BAR

LISTEN TO MUSIC

Combination 1: TV + AUD + MEDIA (Default)

Combination 2: TV + S.BAR + MEDIA

Combination 3: TV + AUD + BLU

Combination 4: AUD only

Combination 5: S.BAR only

TO DELETE A LEARNED FUNCTION, THE PROCEDURE IS:

1. Hold down MAGIC until the LED under the device blinks twice.

The LED under the current mode key will stay lit.

2. Using the DEVICES key, make sure the LED for the device you want

to delete functions from is lit.

3. Press 976 – the LED will blink twice.

4. Press the key to delete twice – the LED will blink twice.

Repeat the above procedure for each key you want to delete.

PLAY GAME

Combination 1: TV + GAME (Default)

Combination 2: TV + GAME + AUD

Combination 3: TV + GAME + S.BAR

CUSTOM

Combination 1: TV + MEDIA (Default)

Combination 2: TV + MEDIA + AUD

Combination 3: TV + MEDIA + S.BAR

Combination 4: TV + GAME

Combination 5: TV + GAME + AUD

Combination 6: TV + GAME + S.BAR

If you set up the default devices for any Activity on the remote (for example a TV and STB

for Watch TV) that Activity will be set up automatically on the remote. If you would like to

change to a diff erent combination, the procedure is as follows:

1. Hold down MAGIC until the LED under the device blinks twice.

The LED under the current mode key will stay lit.

2. Use the ACTIVITY key to scroll through the Activities until the

one you want to set is fl ashing.

3. Press the number of the combination you want to set – e.g 2

for TV + STB + AUD in Watch TV.

4. The LED will blink twice and go out.

To access the Activities, simply press the ACTIVITY key to scroll through until the desired

one is lit. You can return to controlling by device by using the DEVICES key.

INPUT Shift

As the INPUT key is intended to select the input on your TV and most TVs use a menu to

select from a list of inputs, when the INPUT key is pressed in an Activity, the Menu Up,

Down, Left, Right and OK keys temporarily control the TV. If the OK key is pressed, or no

key is pressed for ten seconds, these keys will revert to controlling the relevant device for

the Activity (e.g. STB in Watch TV Mode).

Power Macro

If you hold down the Power key for 2 seconds in any Activity, the remote will send the

Power function for each device contained within that Activity. So for example, holding

Power in the default setting for Watch TV will turn both the TV and Set Top Box on or off .

LEARNING

ACTIVITIES

ACTIVITIES

Smart 8 USA_UK QSG.indd 2 25-06-18 09:57

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je One For All URC 7880 Afstandsbediening. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met One For All. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van One For All URC 7880 Afstandsbediening in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor One For All Afstandsbedieningen
Meer handleidingen voor Afstandsbedieningen

Veelgestelde vragen over One For All URC 7880 Afstandsbediening

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.