Handleiding Ozito BSR-7000 Bandschuurmachine

Handleiding

Power tools that are no longer usable should not be disposed of

with household waste but in an environmentally friendly way. Please

recycle where facilities exist. Check with your local council authority

for recycling advice.

Recyclingpackagingreducestheneedforlandllandrawmaterials.

Reuse of recycled material decreases pollution in the environment.

Please recycle packaging where facilities exist. Check with your

local council authority for recycling advice.

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk

at your local Bunnings Warehouse.

For further information, or any parts not listed here, visit

www.ozito.com.au or contact Ozito Customer Service:

Australia 1800 069 486

New Zealand 0508 069 486

E-mail: [email protected]

V Hz

~ W

/min

n

o

Volts

Alternating current

Revolutions or

reciprocation per minute

Double insulated

Warning

Hertz

Watts

No load speed

Regulator compliance mark

Read instruction manual

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

MAINTENANCE

• Keep the ventilation vents of the sander clean at all times, if possible, prevent

foreign matter from entering the vents.

• After each use, blow air through the sander housing to ensure it is free from

all dust particles which may build up. Build up of dust particles may cause the

sander to overheat and fail.

• If the enclosure of the sander requires cleaning, do not use solvents but a moist

soft cloth only. Never let any liquid get inside the sander; never immerse any

part of the sander into a liquid.

Carbon Brushes

When the carbon brushes wear out, the sander

will spark and/or stop. Discontinue use as soon

as this happens. They should be replaced prior to

recommencing use of the sander. Carbon brushes

are a wearing component of the sander therefore not

covered under warranty. Continuing to use the sander

when carbon brushes need to be replaced may cause

permanent damage to the sander. Carbon brushes

will wear out after many uses but when the carbon brushes need to be replaced,

take the sander to an electrician or a power tool repairer for a quick and low cost

replacement. Always replace both carbon brushes at the same time.

Note: Ozito Industries will not be responsible for any damage or injuries caused

by the repair of the sander by an unauthorised person or by mishandling of the

sander.

IMPORTANT:

If the motor on your belt sander operates but the belt does not rotate, follow these

instructions. In most cases, it isn’t necessary to return the product back to the

store. Check that the drive belt has not been damaged. If it is damaged or broken,

replace with the spare belt provided.

1. To remove and check the drive belt, remove the two screws from the belt

cover. If the belt is damaged, worn or broken, replace with a new drive belt.

2. To remove drive belt, simply use a pair of scissors to cut the drive belt.

Note: DO NOT pry the belt off the pulley as this may damage the housing.

3. Totthenewdrivebelt,placeitaroundthelargebeltwheel.Aligntheridges

on the belt with the teeth on the small gear wheel. Rotate the large belt wheel

and push the drive belt down onto the small gear wheel as it rotates. The wheel

canbedifculttorotateuntilthedrivebeltisfedontothesmallgearwheel.Keep

rotating the wheel and feed the drive belt onto the small gear wheel until it sits

ushwiththeedgeofthewheels.

4. Retcoverandtightenscrews.Repairforaquickandlowcostreplacement.

Always replace both carbon brushes at the same time.

Note: Ozito Industries will not be responsible for any damage or injuries caused

by the repair of the sander by an unauthorised person or by mishandling of the

sander.

TROUBLESHOOTING

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. This is normal

and does not indicate a problem.

Excessive sparking visible through the housing air vents

and/or the sander failing to operate

May indicate the carbon brushes have worn out and need to be

replaced.Carbonbrushesshouldonlybereplacedbyaqualied

electrician or power tool repairer.

Sandpaper Selection

Selecting the correct grit of sandpaper is an important step in achieving optimum

results. Coarse grit will remove the most material. Finer grit will produce a smoother

nish.Theconditionoftheworkpiecewilldeterminethegritofthesandpapertobe

used.Thehigherthegritnumber,thenerthegradeofsandpaper.

If the surface is rough, start with a coarse grit and sand until the surface is uniform.

Medium grit may then be used to remove scratches left by the coarser grit. Finer

gritisthenusedtonishthesurface.Alwayscontinuesandingwitheachgradeof

sandpaper until the surface is uniform.

MATERIAL APPROPRIATE GRIT

Coarse Sanding Fine Sanding

Paintwork 180 400

Wood: Softwood 60 240

Hardwood 60 180

Veneer 240 320

Note: If intermediate sanding is required, choose a grit rating between coarse and

ne.Theabovetableisintendedasaguideonly.Toensureasatisfactoryresult,

asmall,inconspicuousareashouldrstbetestedtoensurethegritofsandpaper

chosenissuitableforthedesirednish.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Ozito BSR-7000 Bandschuurmachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Ozito. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Ozito BSR-7000 Bandschuurmachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Ozito Bandschuurmachines
Meer handleidingen voor Bandschuurmachines

Veelgestelde vragen over Ozito BSR-7000 Bandschuurmachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Ozito USK-3000 Bandschuurmachine

Handleiding

Ozito BSV-9000 Bandschuurmachine

Handleiding

Craftsman 315.117270 Bandschuurmachine

Handleiding

Bosch GBS 100 AE Bandschuurmachine

Handleiding

Hazet 9033 N-4 Bandschuurmachine

Handleiding

Bosch PBS 7 A Bandschuurmachine

Handleiding

Far Tools BS 810C Bandschuurmachine

Handleiding

AEG BHBS18-75BL Bandschuurmachine

Gerelateerde categorieën