Handleiding Philips CMP200 Autoversterker
Handleiding voor je Philips CMP200 Autoversterker nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.
Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.
Handleiding
Loading…
Register your product and get support at
www.philips.com/welcome
CMP200
EN User manual
RU Руководствопользователя
A
G
C
E
F
D
B
a
a
b
c
b
c
English
1. Important
Safety
•
Read and understand all instructions before you use the apparatus. If damage
is caused by failure to follow instructions, the warranty does not apply.
This unit is designed for negative ground (earth) 12 V DC operation only.•
Use only the supplied mounting hardware for a safe and secure installation.•
Do not connect any active speakers (with built-in amplier) to the speaker •
terminals of the unit. Doing so may damage the active speakers.
To ensure safe driving, adjust the volume to a safe and comfortable level.•
To avoid short circuit, do not expose the apparatus to rain or water.•
Never expose the apparatus to direct sunlight, naked ames or heat.•
Clean the apparatus with soft, damp cloth. Never use substances such as •
alcohol, chemicals or household cleaners on the apparatus.
Notice
Environmental information
All unnecessary packaging has been omitted. We have tried to make the
packaging easy to separate into three materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if
disassembled by a specialized company. Please observe the local regulations
regarding the disposal of packaging materials, exhausted batteries and old
equipment.
Any changes or modications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
2009 © Koninklijke Philips Electronics N.V. All rights reserved.
Specications are subject to change without notice. Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners. Philips reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
2. Your car power amplier
Congratulations on your purchase, and welcome to Philips!
To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the amplier, you can enjoy high quality sound performance with
powerful bass and beats.
What’s in the box
A
Check and identify the contents of your package:
a Amplier
b Screw_4x25mm (x4)
c Fuse (x2)
d Hi input connector (x1)
Overview of the main unit
B
a OUTPUT L/R
Connect additional amplier for additional speakers.
•
b
INPUT L/R
• Connect car audio with RCA cable.
c HI INPUT
Connect car audio with the supplied high input connector.
•
d
INPUT LEVEL
Adjust input level (0.3V to 6V).
•
e
PROTECT
Light in red when the PROTECTOR is activated.
•
f
POWER
Light in blue when power is turned on.
•
g
FREQ
Adjust frequency of HPF or LPF from 30Hz to 400Hz.
•
h HPF/OFF/LPF
Select High-pass-lter (HPF), Low-pass-lter(LPF) or OFF (at)
•
mode.
i BASS BOOST
Boost the frequencies at around 45Hz to a maximum of 12dB.
•
j
POWER (GND/REM/+12V)
Connect +12V DC power cable, ground wire and remote wire.
•
k
Fuse: 30Ax2
l SPEAKER OUTPUT
Connect to speakers or subwoofers.
•
3. Installation
Installation
C
You can mount the amplier either under a seat or on the rear tray.
Note
To avoid interference, do not place the amplier too close to the car audio or
•
antenna.
The supplied mounting screws are 25mm long. Make sure that the mounting
•
board is thicker than 25mm.
1
Place the unit on the location for installation.
2
Mark the positions of the four screw holes.
3
Drill the holes with driller of approximately 4mm in diameter.
4
Mount the unit with the supplied screws.
Connect speakers
D
Note
Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a
•
bridged amplier).
Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may
•
degrade sound quality.
Option 1: Mono bridged mode: connect 1 speaker
a
Option 2: Stereo mode: connect 2 speakers
b
Option 3: Tri-mode: connect 3 speakers
c
Connect car audio
E
Option 1: High level input connection
a
Connect the amplier to your car audio with the supplied High level
input connector.
Option 2: Line input connection
b
Connect the amplier to the car audio with a RCA cable (not supplied).
Option 3: Line output connection
c
Connect the amplier to another amplier.
Connect power
F
1
Make the power connection as illustrated below:
Connect the ground wire from the car to the • GND socket.
Connect the remote wire from the car audio to the
• REM socket.
√ With this connection, you can turn on/off the amplier
with the car audio.
Connect the power wire from the car battery to the
• +12V
socket.
Tip
If your car audio does not have remote output, connect the remote input •
terminal (REM) to the accessory power supply.
4. Use your power amplier
Select crossover frequency mode
You can select crossover frequency mode as below:
HPF (high-pass-lter) mode Select this mode when mid-range speakers and
tweeters are connected for high frequency output.
LPF (Low-pass-lter) mode Select this mode when woofer and subwoofer is
connected for low frequency output.
OFF (at) mode Select this mode when tri-mode speaker connection
is used.
1
Slide HPF/OFF/LPF to the selected positon.
Adjust frequency
You can adjust frequency of HPF or LPF from 30HZ to 400Hz.
Note
When the
•
HPF/OFF/LPF switch is set at OFF position, the frequency adjustment
does not work.
1
Rotate FREQ to select frequency.
Adjust input level
You can adjust the input voltage from 0.3V to 6V.
1
Rotate INPUT LEVEL to adjust input voltage.
Adjust bass boost
You can punch extra bass for 0 to 12dB.
1
Rotate BASS BOOST to punch for extra bass.
About the protector indicator
The amplier has a built-in protection circuit to protect the transistors
and speakers when:
The unit is overheated. Or
•
A DC current is generated. Or•
The battery voltage is over low or over high. Or•
The speaker terminals are short circuited.•
When the PROTECT indicator lights up in red, the unit shuts down
automatically. If this happens, please:
1
Take out the disc or tape and turn off the car audio.
2
Check the cause of the malfunction (see above).
3
If the amplier has overheated, wait until the unit cools down
before use.
Replace fuse
G
If there is no power, the fuse may be damaged and need to be replaced.
1
Pull out the damaged fuse.
2
Replace the fuse with the supplied fuses or to buy two fuses
that matches the voltage of the damaged fuse (30Ax2).
If the fuse gets damaged immediately after it has been replaced, there
may be an internal malfunction. In such case, consult your Philips dealer.
5. Product information
Note
Product information is subject to change without prior notice.
•
Power Output (RMS)
- 4 ohm
- 4 ohm (bridged)
- 2 ohm
125Wx2
380Wx1
190Wx2
Total harmonic distortion 0.01%
Signal to noise ratio 106dB
Channel separation 50dB
Frequency response 5-100kHz
Input sensitivity 300mV-6V
Input impedance 22k ohm
Fuse rating 30Ax2
Dimensions (DxWxH) 54.4x336.5x240.2mm
ba
dc
a
lk
j
bc
dfeghi
RL
RL
4 ohm speaker
Динамик 4 Ом
RL
4 ohm speaker 4 ohm speaker
Динамик 4 Ом Динамик 4 Ом
8 ohm speaker
Динамик 8 Ом
RL
4 ohm speaker
Динамик 4 Ом
4 ohm speaker
Динамик 4 Ом
Left speaker
Right speaker
Car audio unit
Левый громкоговоритель
Правый громкоговоритель
Автомобильное
аудиоустройство
White / Black
White
Grey
Grey / Black
Белый
Серый
Белый/черный
Серый/черный
LINE OUT
Car audio unit
Автомобильное
аудиоустройство
Линейный выход
RL
to a metal point of the car
Car audio unit
Remote output
Fuse (60 A)
+12 V car battery
less than 450 mm (18 in)
К металлическому контакту в автомобиле
Выход для пульта ДУ
Автомобильное
аудиоустройство
Менее 450 мм (18 дюймов)
Плавкий предохранитель (60 А)
Автомобильный аккумулятор +12 В
CMP200_51_UM_V2.0_EN+RU.indd 1 12/9/2009 3:21:56 PM
Loading…
Beoordeling
Laat ons weten wat je van de Philips CMP200 Autoversterker vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.Meer over deze handleiding
We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Philips CMP200 Autoversterker. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Philips. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Philips CMP200 Autoversterker in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.
Specificaties
| Merk | Philips |
| Model | CMP200 |
| Categorie | Autoversterkers |
| Bestandstype | |
| Bestandsgrootte | 1.24 MB |
Alle handleidingen voor Philips Autoversterkers
Meer handleidingen voor Autoversterkers
Praat mee over dit product
Laat hier weten wat jij vindt van de Philips CMP200 Autoversterker. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.