Handleiding Phoenix UF0973KD Kluis

Handleiding

Phoenix Safe Company: Where peace  mind is guaranteed

GUARANTEE REGISTRATION

Please submit your guarantee registration by visiting our website www.phoenixsafe.com

and clicking on guarantee registration.

For further assistance or information please contact us on 0151 944 6444.

APEX HOUSE, 1 ORRELL MOUNT, LIVERPOOL,

L20 6NS, UNITED KINGDOM

+44 (0)151 944 6444

PLEASE READ CAREFULLY

INTRODUCTION

To ensure their high security attributes, Underfloor Safes require a High Grade Concrete

Encasement containing suitable reinforcement.

LOCATION

The installation should be undertaken by a qualified installer whose survey would determine a

convenient ground floor site free from any electrical wiring, water or gas pipes, etc., and where the

use of attacking tools would be restricted.

INSURANCE

If the safe is for insurance requirements your insurance company should be made aware of your

intention prior to installation.

WHEN THE INSTALLATION IS COMPLETE NO PORTION OF THE NECK OR DEPOSIT TUBE MUST

PROTRUDE ABOVE FLOOR LEVEL.

SAFE PREPARATION

1. Remove door from safe to a place away from site to avoid any form of contamination.

2. To prevent dust or concrete from entering during installation fill the inside of the safe and neck

with crumpled newspaper.

3. For round door models ensure that the A.B.S neck is fully engaged in the steel collar. Where two

necks are used see that they are correctly located. Single or double A.B.S necks may be glued

to avoid subsequent dislodgement.

4. Apply sealant around neck-to-collar joint.

Replace lid

REINFORCEMENT

Steel reinforcement must be used. A suitable type is Weldmesh Ref. No.26: 2” x 2” (50 mm x

50mm) x 6 S.W.G. Round door safes require a vertical layer approximately 9” (225mm) diameter

by 3” (75mm) high formed to fit around the A.B.S neck. A 30” x 30” (762 mm x 762mm) piece is

notched at the corners and the edges are bent downward leaving a horizontal layer approximately

22” x 22” (560 mm x 560mm). A hole is cut into the mesh to accommodate the neck and to allow

positioning in the concrete 2” (50mm) below floor level. Additional steel reinforcement may be

added to increase concrete protection at sides of safe if required. Reinforcement is arranged

similarly for square door safes with both vertical and horizontal layers.

SITE PREPARATION

1. Remove any floor covering and expose concrete floor.

2. Mark an area on the floor to allow not less than 6” (150mm) of concrete round the sides of the

safe.

3. Cut through the concrete and excavate to a depth of 3” (75mm) more than the total depth of the

safe.

4. Angle the sides of the hole outwards by 2” in order that the concrete is dovetailed into the floor.

5. For installation in a wooden floor it will be necessary to confine the concrete to the dimensions

given with the use of shuttering.

CONCRETE PREPARATION AND DAMP-PROOFING

Use only good quality sand, aggregate and cement.

Recommended Specification:

PARTS BY WEIGHT

Coarse Graded Aggregate ¾” MAX 3

Fine Graded Aggregate 3/16” MAX 1 ½

Ordinary Portland Cement 1

Water Not to exceed 24.4 litres for every 50 kgs of Cement

All materials to conform to the appropriate Bristish Standard Specification.

A suitable dry mix preparation is Marley Mix 3-1 ½ - 1 B.S 5838 Part 1

DO NOT CONCRETE UNLESS THE AMBIENT TEMPERATURE IS AT LEAST 3ºc MIN.

INSTRUCTIONS FOR INSTALLING UNDERFLOOR SAFES IN

CONCRETE AND WOODEN FLOORS & GUARANTEE REGISTRATION

Materials must be frost free and in cold conditions use water heated to 10ºC. Accelerating or other

admixtures containing calcium chloride must not be used as these are highly corrosive. The

addition of a waterproofing agent, however, may be necessary. Where site excavation reveals

extreme damp presence, the hole should be lined with a heavy gauge polythene sheeting.

Thoroughly dry mix all materials and then add a minimum of water to allow the concrete to be

compacted. Do not add too much water as this will reduce the strength of the construction. The

amount of water shown in the column above produces a 2” (50 mm) slump which should not be

exceeded.

SAFE INSTALLATION

1. Cover the base of the hole with 4” (100 mm) of the concrete mix.

2. Lift safe by top plate (avoid dislodging round type neck), place in centre of hole and work down

into the concrete bed until the lid is at the correct level with surrounding floor.

3. Use a spirit level to span the hole to check the safe is level.

4. The concrete is added in layers of 4” (100mm): each layer worked well into the previous layer

with a tamping tool. A section of timber, or similar, about 39” (1m) long, with a ramming face

approximately 1” (25mm) square is ideal for the purpose. Work methodically over entire surface

and ensure full compaction of concrete. Take care not to disturb the safe or dislodge the neck

through-out installation.

5. The steel reinforcement is introduced into the concrete at the appropriate stage.

6. When the hole is filled with the concrete mix to within ½ “ (12mm) of the surface, take the safe

door from bag and after removing lid, insert door into safe to ensure that misalignment has not

occurred. ANY NECESSARY ADJUSTMENT WOULD NEED TO BE MADE NOW BEFORE

CONCRETE IS SET.

7. Screed last ½“ (12mm) with a mixture of sand and cement to bring to a smooth finish.

THE SAFE MUST NOT BE USED FOR 14 DAYS AFTER INSTALLATION.

CARE AND MAINTENANCE

The subsequent application of a lino paint by the owner/user will act as a surface stabiliser and

help to control grit. Ensure that any floor washing activity etc. does not result in water entering the

safe. Keep safe door and locating collar dry, clean and lightly oiled. Dirt and grit etc. can be

damaging to the locking mechanism. To ensure that the safe remains in good working order

always close the escutcheon and see that the lid is replaced properly after use. The use of silica

gel is recommended where condensation is a problem or where the safe remains locked for any

extended period of time.

Version 1/MH/FEB 16

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Phoenix UF0973KD Kluis. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Phoenix. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Phoenix UF0973KD Kluis in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Phoenix Kluizen
Meer handleidingen voor Kluizen

Beoordeling

Veelgestelde vragen over Phoenix UF0973KD Kluis

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Phoenix SS0998FD Kluis

Handleiding

Phoenix UF0643KD Kluis

Handleiding

Phoenix FS1922E Kluis

Handleiding

Phoenix UF0613KD Kluis

Handleiding

Phoenix SS1193E Kluis

Handleiding

Phoenix UF0662K Kluis

Handleiding

Phoenix SS1191E Kluis

Handleiding

Phoenix SS1182E Kluis

Gerelateerde categorieën