Handleiding Planet FSD-604HP Switch

Handleiding

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Check the following contents of your package:

FSD-604HP User’s Manual

Foot Pad Power Cord

If any of these are missing or damaged, please contact your

dealer immediately.

 Switching

 Hardware-based 10/100Mbps auto-negotiation and auto

MDI/MDI-X

 Flow control for full duplex operation and back pressure

for half duplex operation

 1536bytes packet size

 Integrates address look-up engine, supporting 2K absolute

MAC addresses

 Automatic address learning and address aging

 Solid DIP switch to isolate ports to prevent broadcast

storm and defend DHCP spoong

 Hardware

 Desktop palm size

 LED indicators for PoE ready/activity and LINK/ACT

 Supports Contact Discharge of ±4KV DC and Air Discharge

of ±6KV DC for Ethernet ESD protection

 Supports ±4KV Surge Immunity

 Internal AC power supply

 Fanless design

5. Switch Rear Panel

Figure 5-1 shows the rear panel of the FSD-604HP.

100-240V , 50/60Hz, 2A max.

Figure 5-1: FSD-604HP Rear Panel

Power

Note

1. The device is a power-required device, meaning

it will not work till it is powered. If your

networks should be active all the time, please

consider using UPS (Uninterrupted Power

Supply) for your device. It will prevent you from

network data loss or network downtime.

2. In some areas, installing a surge suppression

device may also help to protect your FSD-604HP

from being damaged by unregulated surge or

current to the FSD-604HP.

Extend PoE Mode

Standard PoE Mode

Power

PoE IP Camera

PoE

10BASE- T UTP with PoE

PoE

100BASE- TX UTP with PoE

PoE

100 meters (328 feet)

FSD-604HP

FSD-604HP

Power

PoE

250 meters (820 feet)

PoE IP Camera

Standard

Extend

Standard

Extend

Note

After changing the mode, you need to manually

restart the FSD-604HP to make the corresponding

configuration take effect.

2. Product Features

 RJ45 Interface

 6-port 10/100TX Ethernet RJ45 copper

 4-port IEEE 802.3af/at PoE Injector (Port-1 to Port-4)

 Power over Ethernet

 Complies with IEEE 802.3af/at Power over Ethernet end-

span PSE

 Up to 4 IEEE 802.3af/2 IEEE 802.3at devices powered

 Supports PoE power up to 30 watts for each PoE port

 60-watt PoE budget

 Hardware DIP switch for “Standard” and “Extend” mode

selection; the “Extend” mode features 30-watt PoE

transmit distance of 250m at speed of 10Mbps and VLAN

isolation

 Auto detects powered device (PD)

 Circuit protection prevents power interference between

ports

 Remote power feeding up to 100m in standard mode

3. Switch Front Panel

Figure 3-1 shows the front panel of the FSD-604HP.

PoE

1 2 3 4

5 Uplink 6

ACTLNK

PoE-in-Use

FSD-604HP

PWR

Standard

Extend

Figure 3-1: FSD-604HP Front Panel

The front panel of the FSD-604HP provides one DIP switch

for “Standard” and “Extend” mode selections. The detailed

descriptions are shown in the following table.

DIP Switch

Mode

Function

Standard

(default)

This mode makes the FSD-604HP operate

as a general switch and all ports operate at

10/100Mbps auto-negotiation.

Extend

This mode makes the FSD-604HP operate as

a VLAN isolation switch and port 1 to port 4

will isolate respectively. Port 1 to port 4 can

communicate with port 5~6 (uplink port).

This mode also makes the FSD-604HP

operate at auto–negotiation 10Mbps speed

duplex mode only, but the delivery distance

of PoE power and network data can reach

250m.

4. LED Indicators

System

LED Color Function

PWR Orange Lights to indicate the Switch has power.

Per 10/100Mbps Port

LED Color Function

PoE Orange

Lights to indicate the port is providing

52V DC in-line power to remote PoE PD.

LNK/ACT Green

Lights to indicate the link through

that port is successfully established at

10/100Mbps.

Blinks to indicate that the Switch is

actively sending or receiving data over

that port.

6. Installing the Switch

This part describes how to install your FSD-604HP and make

connections to it. Please read the following topics and follow

the procedures as presented.

Note

This FSD-604HP does not need software

configuration.

Desktop Installation

To install the FSD-604HP on desktop, simply follow the

following steps:

Step 1: Place the FSD-604HP on desktop near an electrical

outlet.

Step 2: Keep enough ventilation space between the

FSD-604HP and the surrounding objects.

Note

When choosing a location, please keep in mind the

environmental restrictions discussed in Chapter 7 --

Product Specifications.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Planet FSD-604HP Switch. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Planet. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Planet FSD-604HP Switch in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Planet Switches
Meer handleidingen voor Switches

Beoordeling

Gerelateerde producten

Handleiding

Planet SW-804 Switch

Handleiding

Planet FNSW-2401 Switch

Handleiding

Planet FSD-503 Switch

Handleiding

Planet GSW-1820HP Switch

Handleiding

Planet GSD-503 Switch

Handleiding

Planet GSW-2620VHP Switch

Handleiding

Planet FSD-803 Switch

Handleiding

Planet GSW-1820VHP Switch

Gerelateerde categorieën