Handleiding Poulan PL914 Kettingzaag

Handleiding

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off

balance.

• Carry the chain saw by the front handle with the

chain saw switched off and away from your body.

When transporting or storing the chain saw always

apply the guide bar cover. Proper handling of the

chain saw will reduce the likelihood of accidental

contact with the moving saw chain.

• Follow instructions for lubricating, chain

tensioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

• Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

of control.

• Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw

for cutting plastic, masonry or non-wood building

materials. Use of the chain saw for operations

different than intended could result in a hazardous

situation.

Causes and operator prevention of kickback

Kickback may occur when the nose or tip of the guide

bar touches an object, or when the wood closes in and

pinches the chain in the cut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control

of the chain saw which could result in serious personal

injury. Do not rely exclusively upon the safety devices built

into your chain saw. As a chain saw user, you should take

several steps to keep your cutting jobs free from accident

or injury.

.LFNEDFNLVWKHUHVXOWRIWRROPLVXVHDQGRULQFRUUHFW

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

 0DLQWDLQD¿UPJULSZLWKWKXPEVDQG¿QJHUV

encircling the chain saw handles, with both hands

on the chain saw and position your body and arm

to allow you to resist kickback forces. Kickback

forces can be controlled by the operator, if proper

precautions are taken. Do not let go of the chain saw.

• Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and

enables better control of the chain saw in unexpected

situations.

• Only use replacement bars and saw chains

VSHFL¿HGE\WKHPDQXIDFWXUHU Incorrect

replacement bars and saw chains may cause saw

FKDLQEUHDNDJHDQGRUNLFNEDFN

• Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

INSTRUCTIONS CONCERNING THE PROPER

TECHNIQUES FOR BASIC FELLING, LIMBING,

AND CROSS-CUTTING

Felling a tree

When bucking and felling operations are being performed

by two or more persons at the same time, the felling

operations should be separated from the bucking

operation by a distance of at least twice the height of the

tree being felled. Trees should not be felled in a manner

that would endanger any person, strike any utility line or

cause any property damage. If the tree does make contact

ZLWKDQ\XWLOLW\OLQHWKHFRPSDQ\VKRXOGEHQRWL¿HG

immediately.

The chain saw operator should keep on the uphill side of

the terrain as the tree is likely to roll or slide downhill after

it is felled.

An escape path should be planned and cleared as

necessary before cuts are started. The escape path

should extend back and diagonally to the rear of the

expected line of fall as illustrated.

Before felling is started, consider the natural lean of the

tree, the location of larger branches and the wind direction

to judge which way the tree will fall.

Remove dirt, stones, loose bark, nails, staples and wire

from the tree.

Notching undercut

0DNHWKHQRWFKWKHGLDPHWHURIWKHWUHHSHUSHQGLFXODU

to the direction of falls as illustrated. Make the lower

KRUL]RQWDOQRWFKLQJFXW¿UVW7KLVZLOOKHOSWRDYRLGSLQFKLQJ

either the saw chain or the guide bar when the second

notch is being made.

Felling back cut

Make the felling back cut at least 50 mm higher than the

horizontal notching cut as illustrated. Keep the felling back

cut parallel to the horizontal notching cut. Make the felling

back cut so enough wood is left to act as a hinge. The

hinge wood keeps the tree from twisting and falling in the

wrong direction. Do not cut through the hinge.

As the felling gets close to the hinge, the tree should begin

to fall. If there is any chance that the tree may not fall in

desired direction or it may rock back and bind the saw

chain, stop cutting before the felling back cut is complete

and use wedges of wood, plastic or aluminium to open the

cut and drop the tree along the desired line of fall.

When the tree begins to fall remove the chain saw from

the cut, stop the motor, put the chain saw down, then

use the retreat path planned. Be alert for overhead limbs

falling and watch your footing.

A. Notch

7

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Poulan PL914 Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Poulan. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Poulan PL914 Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Poulan Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over Poulan PL914 Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Poulan P4018AV BH Kettingzaag

Handleiding

Poulan PL1416 Kettingzaag

Handleiding

Poulan P3314WSA Kettingzaag

Handleiding

Poulan P3416 Kettingzaag

Handleiding

Poulan P3314WS Kettingzaag

Handleiding

Poulan P4018WM Kettingzaag

Handleiding

Poulan PRCS16i Kettingzaag

Handleiding

Poulan PL3816 Kettingzaag

Gerelateerde categorieën