Handleiding Rodex RDX9617 Druksproeier

Handleiding

8

• The CHARGING ADAPTER features intelligent charging– constant current/constant voltage/maintenance

and short-circuit/ over-current/inverse-connection protection.

The charger indicator lamps are as follows:

 Red=Charging

 Green=Charged/Stand-by.

USING THE MACHINE

SPRAY APPLICATION

• There is no harm in applying in slightly windy and cool weather. For example, it is recommended

for spraying early in the morning or early in the afternoon. This will reduce the evaporation of

chemicals and increase the protection effect.

• The implementer should move in the direction of the wind.

• If chemical splashes into your mouth or eyes, rinse immediately with clean water and see a doctor.

• If the practitioner has a headache or anxiety, they should stop working and see a doctor

immediately.

• After working, wash your hands and clean your clothes. Any remaining insecticide can also infect

other items you touch.

There are four nozzles to choose from.

• FLAT FAN NOZZLE sprays a pattern that is a fan configuration in one axis and flat in the other axis.

• 5-Hole Adjustable NOZZLE sprays a light misty cone pattern or a full saturated spray pattern

depending on the adjustment of the nozzle.

• 4-Hole Adjustable NOZZLE sprays a jet pattern or a full saturated spray pattern depending on the

adjustment of the nozzle.

• DOUBLE Conical Spray NOZZLE sprays a dual cone shapes with fluid flow throughout the 2 cone

angles.

Application Instructions

Preparations before starting:

1. Charge the battery until the charger’s Green / “Charged” light comes on indicating that the battery

is fully charged.

2. Never operate the sprayer without liquid in it or it may damage the diaphragm.

3. In case of humming sound from inside the sprayer or poor atomization after long time use,

recharge the battery.

- Battery must be charged at least 3 hours. Keep charger in a dry, well ventilated safe place.

4. Test sprayer with water prior to use to assure that no leakage occurs and that proper atomization

occurs.

SPRAYING

A. Before adding the chemical liquid, spray water so you can see if there is any leakage.

After the chemical liquid has been added, it should not be filled too quickly and the tank should not

be completely filled. It should be checked that the liquid will pass through the filter and it should be

ensured that foreign material leakage is prevented. The mouth of the tank should be well sealed to

prevent leakage. The machine should not be turned off while adding liquid, but should be operated

at a slow speed.

B. Pressure regulation; adjust the pressure of the escaping liquid. This was done before leaving the

factory. Perform this action if possible.

C. Put the machine in reverse. Turn the spray valve and start spraying.

D. Some important notes for spraying are as follows.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Rodex RDX9617 Druksproeier. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Rodex. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Rodex RDX9617 Druksproeier in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Rodex Druksproeiers
Meer handleidingen voor Druksproeiers

Beoordeling

Gerelateerde producten

Handleiding

Rodex RDX9618 Druksproeier

Handleiding

Rodex RDX9610 Druksproeier

Handleiding

Rodex RDX9619 Druksproeier

Handleiding

Clarke HSP2 Druksproeier

Handleiding

Stihl SGA 85 Druksproeier

Handleiding

Parkside IAN 437353 Druksproeier

Handleiding

Silvan 190545 Druksproeier

Handleiding

Clarke CSK6 Druksproeier

Gerelateerde categorieën