Hood Description - Fig. 1
1) Control panel
2) Metal grease filter
3) Worktop illumination
Use: Two systems are available
Exhaust mode (S)
Vapours are extracted outside through an
exhausting pipe that is affixed to the con-
nection ring above the hood.
Diameter of the exhausting pipe must be
equal to that of the connection ring.
In the horizontal runs the duct must be
slightly slanted (about 10°) and directed
upwards to vent the air easily from the room
to the outside.
Attention!
If the hood is supplied with carbon filter
then it must be removed.
Filter version (K)
The air is filtered through a carbon filter
(for its installation see paragraph “Car-
bon filter”) and recirculated into the room
through the grating on the lower side of the
chimney.
Attention!
If the hood is not supplied with carbon
filter, then it must be ordered and
mounted.
This version is used when there is no ex-
haust duct for venting outdoors or when it
is impossible to install one.
Installation
When installed, the distance between ex-
tractor and hob gas burners or electric plates
must be not less than 65 cm providing the
total hob output does not exceed 11kw.
For each kw in addiction, the distance be-
tween extractor and hob gas burners must
be increased of 10 cm.
Electric connection
Before completing any connection make sure
the house voltage corresponds with the
voltage indicated on the label affixed inside
the hood.
It is advisable to call a qualified technician to
make the electrical connection.
Appliance fitted with plug
Connect it to a socket which conforms with
current regulations.
If you intend to connect it directly to the elec-
tric mains, remove the plug and fit an ap-
proved bipolar switch with a minimum con-
tact opening of no less than 3mm.
If the plug is not accessible once it has been
inserted in the socket, it will however be nec-
essary to fit an approved bipolar switch with
a minimum contact opening of no less than
3mm.
Appliance without plug
Fit an approved plug or an approved bipolar
switch with a minimum contact opening of
not less than 3mm.
The manufacturer is not liable for any
problems caused by the user’s failure to
observer the above instructions.
Fastening of shelves (optional)
Fasten the four side supports I to the
adjacent cabinets and place the shelf on
the supports (Fig. 4).
Using the hood
– The hood is provided with a motor with
several speeds For the best performan-
ce, we recommend using the low speeds
in normal conditions and the high speeds
in particular cases of strong odour and
vapour concentration.
– We recommend starting up the hood a
few minutes before cooking and keeping
it running until all the odours have been
eliminated.
Warning!
– The hood cannot be connected to flues
of other appliances that run on energy
sources other than electricity.
– When the hood is used at the same time
of other appliances that run on energy
sources other than electricity, provision
must be made for an adequate air supply.
– No food must be cooked flambé under-
neath the hood.
The use of an unprotected flame is dan-
gerous for the filters and could cause fires.
Therefore, never use an open flame under
the hood. When frying foods, never leave
the pan alone because the cooking oil
could flare up.
– Please, keep to the provisions of official
directives regarding the question of fume
discharge.
– The manufacturer refuses to accept any
responsibility for damage to the hood or
its catching on fire because of failure to
observe the above instructions.
Maintenance
Before performing any maintenance opera-
tion, isolate the hood from the electrical
supply by switching off at the connector and
removing the connector fuse.
Or if the appliance has been connected
through a plug and socket, then the plug
must be removed from the socket.
Metal grease filter (2 or 3 pieces)
The metal grease filter lasts forever and
must be washed either by hand or in the
dishwasher (65°C) with suitable detergents.
The grease fiilters must be washed at
least once a month.
Remove the filter using the handles desi-
gned for this purpose by pulling the filter
backwards and then downwards (Fig. 2).
Let the filter dry without damaging it before
putting it back into place.
Carry out the above steps in reverse orde, to
put the filters back after having washed them.
Carbon filter (2 pieces)
This filter dissolves cooking odours.
The carbon filter must never be washed.
It should be changed every 4 months with
normal use.
Mounting and replacing the carbon filter:
a) Disconnect the hood from the electricity.
b) Remove the metal grease filters (Fig. 2).
c) If the filters have not been installed, place
one filter on each side so that they cover
the grates protecting the rotor on the
motor. Then turn the center handle for the
filters in the clockwise direction (Fig. 3).
d) If the charcoal filters have already been
installed (covering the grates protecting
the rotor on the motor) and must be
replaced, turn the central handle in the
counter-clockwise direction until the filters
are unlocked.
e) Refit the the metal grease filters.
Cleaning
To clean the outside of the hood use a cloth
moistened with denatured alcohol or neutral
liquid detergents. Never use products con-
taining abrasive.
Wipe brushed stainless steel in the same
direction as the brushing to avoid scratching.
Attention
Failure to observe the rules for cleaning the
appliance and changing and cleaning the
filters can cause fires.
Therefore, we recommend observing these
instructions.
Replacing the lamp
a) Disconnect the hood from the electricity.
b) Remove the grease filters (Fig. 2).
c) Illumination: always replace burnt-out
lamps with 40 Watt max. (E14) (Fig. 5) -
20 Watt max. (Fig. 6) and 11 Watt max.
(Fig. 7).
d) Refit the the metal grease filters.
e) Before calling for repair service because
the hood fails to light up, make sure the
bulbs are screwed in tightly.
GB GB
6 7
Praat mee over dit product
Laat hier weten wat jij vindt van de Rosières RDR 61 BMV Afzuigkap. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.