Handleiding Ryobi RCS2340B Kettingzaag

Handleiding

7

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician.

WARNING

Injuries may be caused, or aggravated, by prolonged

use of a tool. When using any tool for prolonged periods,

ensure you take regular breaks.

SAFETY DEVICES

Low kick-back saw chain

A low-kickback saw chain helps to reduce the possibility of

a kickback event.

The rakers (depth gauges) ahead of each cutter can

minimize the force of a kickback reaction by preventing the

cutters from digging in too deeply. Only use replacement

guide bar and chain combinations recommended by the

manufacturer.

As saw chains are sharpened, they lose some of the low

kickback qualities and extra caution is required. For your

safety, replace saw chains when cutting performance

decreases.

Spiked bumper

The integral bumper spike may be used as a pivot when

making a cut. It helps to keep the body of the chainsaw

steady while cutting. When cutting, push the product

forward until the spikes dig into the edge of the wood, then

by moving the rear handle up or down in the direction of

the cutting line it can help ease the physical strain of cutting

Guide bars

Generally, guide bars with small radius tips have somewhat

lower potential for kickback. You should use a guide bar

and matching chain which is just long enough for the job.

Longer bars increase the risk of loss of control during

sawing. Regularly check the chain tension. When cutting

smaller branches (less than the full length of the guide bar)

the chain is more likely to be thrown off if the tension is

not correct.

Chain brake

Chain brakes are designed to quickly stop the chain from

rotating. When the chain brake lever/hand guard is pushed

towards the bar, the chain should stop immediately. A

chain brake does not prevent kickback. It only lowers the

risk of injury should the chain bar contact the operator’s

body during a kickback event. The chain brake should be

tested before each use for correct operation in both the run

and brake positions.

Chain catcher

A chain catcher prevents the saw chain from being thrown

back towards the operator if the saw chain comes loose

or breaks.

ASSEMBLY

WARNING

If any parts are damaged or missing, do not operate the

product until the parts are replaced. Failure to heed this

warning could result in serious personal injury.

ADJUSTING THE CHAIN TENSION

See page 25.

1. Disconnect the product from the power supply. Wear

protective gloves.

2. To correct the chain tension, fully loosen the chain

tension/guide bar locking knob, then tighten the chain

tension/guide bar locking knob by turning it clockwise

until it locks into place. Check the chain tension

frequently.

The chain tension is correct when the gap between the

cutter in the chain and the bar is between 3 mm - 4

bar downwards (away from the bar) and measure the

distance between the bar and the chain cutters.

3. Tighten and lock the chain tension/guide bar locking

knob by turning it clockwise.

OPERATION

ADDING CHAIN LUBRICATING OIL

See page 15.

WARNING

Never work without chain lubricant. If the saw chain is

running without lubricant, the guide bar and saw chain

can be damaged. It is essential to frequently check the

oil level in the oil level gauge and before starting to use

the chainsaw.

1. Clear surface around the oil cap to prevent

contamination.

2. Unscrew and remove the cap from the oil tank.

3.

gauge. Ensure that no dirt enters the oil tank while

filling.

4.

any spillage.

5. One full oil tank will enable you to use the saw for 18

- 28 min.

HOLDING THE CHAIN SAW

See page 15.

Always hold the chain saw with your right hand on the rear

handle and your left hand on the front handle. Grip both

Ensure that your left hand is holding the front handle so

that your thumb is underneath.

Downloaded from www.Manualslib.com manuals search engine

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Ryobi RCS2340B Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Ryobi. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Ryobi RCS2340B Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Ryobi Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over Ryobi RCS2340B Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Ryobi RCS-3535C2 Kettingzaag

Handleiding

Ryobi OCS1830 Kettingzaag

Handleiding

Ryobi RCS4240B Kettingzaag

Handleiding

Ryobi RCS2340 Kettingzaag

Handleiding

Ryobi RC3535B Kettingzaag

Handleiding

Ryobi RCS36X3550HI Kettingzaag

Handleiding

Ryobi RCS4040CB Kettingzaag

Handleiding

Ryobi RY40502B Kettingzaag

Gerelateerde categorieën