Handleiding Sharp R-405K Magnetron

Handleiding

5

This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug.

It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National

Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk

of electric shock by providing an escape wire for the electric current.

WARNING – Improper use of the grounding plug can result in a risk of electric shock.

Electrical Requirements

The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more

protected electrical supply. It is recommended that a separate circuit serving

only this appliance be provided.

The oven is equipped with a 3-prong grounding plug. It must be plugged into a

wall receptacle that is properly installed and grounded. Should you only have a

2-prong outlet, have a qualifi ed electrician install a correct wall receptacle.

A 3-prong adapter may be purchased and used temporarily if local codes allow.

Follow package directions.

A short power-supply cord is provided to reduce risk of becoming entangled in

or tripping over a longer cord.

Extension Cord

If it is necessary to use an extension cord, use only a 3-wire extension cord that

has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug

on the microwave oven. The marked rating of the extension cord should be AC

115-120 volt, 15 amp. or more.

Be careful not to drape the cord over the countertop or table where it can be

pulled on by children or tripped over accidentally.

Notes:

1. If you have any questions about the grounding or electrical instructions, consult

a qualifi ed electrician or service person.

2. Neither Sharp nor the dealer can accept any liability for damage to the oven

or personal injury resulting from failure to observe the correct electrical connection procedures.

Radio or TV Interference

Should there be any interference caused by the microwave oven to your radio or TV, check that the microwave oven

is on a different electrical circuit, relocate the radio or TV as far away from the oven as feasible or check position

and signal of receiving antenna.

GROUNDING INSTRUCTIONS

Permanent and Correct Installation

3-Prong Plug

3-Prong Receptacle

Ground

Receptacle Box

Ground

Receptacle Box

–

Unpacking and Examining Your Oven

1. Remove all packing materials from inside the oven

cavity. DO NOT REMOVE THE WAVEGUIDE

COVER, which is located on the right cavity wall.

Read enclosures and SAVE the Operation Manual.

2. Remove the feature

sticker, if there is one,

from the outside of

the door.

Check the oven for any

damage, such as mis-

aligned or bent door,

damaged door seals

and sealing surfaces,

broken or loose door

hinges and latches

and dents inside the

cavity or on the door.

If there is any damage, do not operate the oven and

contact your dealer or SHARP AUTHORIZED SER-

VICER.

Choosing a Location for Your Oven

You will use the oven frequently so plan its location for

ease of use. It's wise, if possible, to have counter space

on at least one side of the oven. Allow at least 2 inches on

the sides, top and at the rear of the oven for air circula-

tion. Do not place or install the oven in any area where

heat and steam are generated; for example, next to or

above a conventional gas or electric range or above a

conventional wall oven. Heat and steam may damage

the electronics or the mechanical parts of the oven.

Built-in Kit

Your oven can be built into a cabinet or wall—not near

or above a heat source—using Sharp’s white Built-In Kit

RK-40W24 for R-402JW, black RK-40K24 for R-402JK or

R-403KK or stainless steel RK-40S24 for R-405KS. If your dealer

does not stock the kit, it can be ordered directly from the Sharp

Accessories and Supplies Center. Have your credit card

number available and call toll-free: 1-800-237-4277 for

ordering the kit to be sent to your address.

The kit includes ducts, fi nish trim strips and easy-to-

follow instructions for installation as well as the location

of the power supply.

UNPACKING AND INSTALLATION INSTRUCTIONS

402J 403K 405K manual_418.indd 5402J 403K 405K manual_418.indd 5 16.03.2006 11:49:13 Uhr16.03.2006 11:49:13 Uhr

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sharp R-405K Magnetron. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sharp. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sharp R-405K Magnetron in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Sharp Magnetrons
Meer handleidingen voor Magnetrons

Veelgestelde vragen over Sharp R-405K Magnetron

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Sharp R-2348V-BK Magnetron

Handleiding

Sharp R-1851 Magnetron

Handleiding

Sharp SMD2443JSC Magnetron

Handleiding

Sharp YC-MG81E-W Magnetron

Handleiding

Sharp R-2031E-GL Magnetron

Handleiding

Sharp SMD3077ASC Magnetron

Handleiding

Sharp R-7180B Magnetron

Handleiding

Sharp R-2030E-CH Magnetron

Gerelateerde categorieën