Handleiding Silverlit V-22 Osprey Radiobestuurbare helikopter

Handleiding

Battery requirement for Transmitter:

Battery requirement for Helicopter:

Special Note to Adults:

- Regularly examine for damage to the plug, enclosure and other parts. In the event of any damage,

the toy must not be used with the transmitter charger until the damage has been repaired.

- This toy must only be used with the recommended charger.

- Do not try to charge other batteries with transmitter charger.

Helicopter is equipped with a LiPo rechargeable battery,

please pay attention to the following cautions for safety use:

- Do not dispose the battery in fire or heat.

- Do not use or leave the battery near a heat source such as fire or heater.

- Do not strike or throw the battery against hard surface.

- Do not immerse the battery in water, and keep the battery in a cool dry environment.

- When recharging, only use the battery charger specifically for that purpose.

- Do not over-discharge the battery.

- Do not connect the battery to an electrical outlet.

- Do not directly solder the battery and pierce the battery with a nail or other sharp object.

- Do not transport or store the battery together with metal objects such as necklaces, hairpins etc.

- Do not disassemble or alter the battery.

- Charge the battery every 6 months.

Care and Maintenance:

- Always remove batteries from the toy when it is not being used for a long period of time. (Transmitter

only)

- Wipe the toy gently with a clean damp cloth.

- Keep the toy away from direct heat.

- Do not submerge the toy into water that can damage the electronic assemblies.

Note:

- Parental guidance is recommended when installing or replacing batteries.

- Under the environment with electrostatic discharge, the toy may malfunction and require user to

reset the toy.

- New and alkaline batteries are recommended to use in this toy to obtain best and maximum

performance.

Battery Cautions

- Non-rechargeable batteries are not to be recharged.

- Rechargeable batteries are to be removed from the transmitter before being charged. (Transmitter only)

- Rechargeable batteries are only to be charged by an adult.

- Different types of batteries or new and used batteries are not to be mixed. (Transmitter only)

- Only batteries of the same or equivalent type as recommended are to be used.

- Batteries are to be inserted with correct polarity.

- Exhausted batteries are to be removed from the transmitter.

- The supply terminals are not to be short-circuited.

- Do not mix old and new batteries. (Transmitter only)

- Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. (Transmitter only)

Transmitter

Helicopter

- For controlling the sticks on transmitter, try not to push the sticks immediately any extreme

positions. It should be like steering a bicycle rather than pressing computer game sticks.

- For the novice pilot (after the trimming procedure is completed), it is highly recommended to

focus exclusively on learning to control the throttle stick first. If the helicopter turns around by

itself there is no need to keep it straight. For the first flight, it is important to learn to keep the

helicopter at a constant altitude of around 1 meter with very gentle inputs on the throttle stick.

Once the pilot masters this, he may start learning to take control with the direction stick.

The crossed-out dustbin symbol indicates that batteries, rechargeable batteries,

button cells, battery packs, etc. must not be put in the household waste. Batteries

are harmful to health and the environment. Please help to protect the environment

from health risks. Tell your children to dispose of batteries properly by taking them

to the local collecting points. This way batteries are recycled safely.

WEEE

When this appliance is out of use, please remove all batteries and dispose of them

separately. Bring electrical appliances to the local collecting points for waste electrical

and electronic equipment. Other components can be disposed of in domestic refuse.

Do not touch the running propeller!

Do not play above someone's head!

Adult supervision is required!

WARNING:

CHOKING HAZARD - Small parts.

Not for Children under 3 years.

Parts Identification

Troubleshooting

Tips For Trimming

Flying Your Helicopter

Battery Installation & Charging

Safety Precautions:

Warning:

Changes or modifications to this product not expressly approved by the party responsible for compliance

could void the user's authority to operate the product.

- The transmitter-charger is tailor-made for the LiPo rechargeable battery used in Helicopter. Do not use it to charge

any battery other than that in the Helicopter.

Tip! CONTROLLING

Helicopter Transmitter Instruction Manual

Delivery contents

Precautions, Warning & Statement

- After you crash your helicopter, you need to restart the helicopter by slide it’s power

switch to “OFF” and then check for damages. If there is no damage slide the power

switch to “ON” again.

- Don’t operate the helicopter under the direct bright light it will affect the control

system of your helicopter.

- Don’t cover the IR Diode of the transmitter as it will block the IR signal.

- Don’t stick any other label onto the helicopter as it will affect receiving of IR signal.

Tip! OPERATION

- Put the helicopter on a smooth surface. Uneven floor surface will affect its lifting off.

- Slowly increase the throttle.

- Do not look at the transmitter but focus on the helicopter.

- As soon as the helicopter leaves ground, reduce the throttle slightly. (in the worst case, helicopter will go back to the floor,

but that is better than crashing against the ceiling)

- Very gently add the throttle if the helicopter descends.

- Very gently reduce the throttle if the helicopter ascends.

- For turning, give short and small inputs to the direction stick. (most beginners will easily overcontrol the helicopter)

3. Lift-off procedures (after Trimming procedure):

Symptom Cause Correction

Suddenly stop and drop down when flying.

The helicopter does not response. - The helicopter and/ or the transmitter is switch off ("OFF").

- The battery of the helicopter is weak.

- Set the power switch to "ON"

- Recharge the battery of the helicopter.

- Recharge the battery of the helicopter.- The battery of the helicopter is weak.

The helicopter does not react. - Select the correct band.- Band selection on transmitter is not correct.

- Another infrared control device using the same

frequency band.

- Affected by strong lighting.

- Tail rotor blade is deformed or distorted.

- Avoid these if possible, or choose another place to

operate the helicopter.

- Change another environment to avoid direct lighting.

- Replace the tail rotor blade with the spare one provided.

Loss of control.

ENGLISH 1

ENGLISH 3

4 ENGLISH

2 ENGLISH

1. Open the battery compartment by

loosening the screw.

2. Insert 6 AA batteries in the battery

compartment with correct polarity.

3. Close the battery compartment.

Note: 1. The helicopter can operate for about 5 - 6 minutes per every 20 - 30 minutes charging.

2. Before recharging the battery, wait 10 - 15 minutes for it to cool down.

Note: When the power indicator on the transmitter starts blinking, replace the batteries with the aforementioned procedures.

- Parents: Please read the operating instructions carefully with your children prior to the first use.

- This product is designed for indoor use only. Wind and short transmission range can lead to

loss of control.

- Fly the helicopter only in open indoor areas and keep clear of obstacles.

- Pay attention! Do not fly the helicopter near persons and animals.

- Always keep your eyes on the helicopter and prevent it from landing or crashing near your

head, your body, or on other people.

- Never take apart or attempt to modify the product. This could damage the product.

- Always keep rotating parts away from your hands, hair or face to avoid injury. Stand during

operation in order to get out of the way of the helicopter quickly if necessary.

- Always switch the helicopter and the transmitter off when not operating.

- Never allow young children to use this product without adult supervision.

- Never use this product if it has damaged parts.

- Never hold or throw any objects into the running rotors.

- Keep hands, hair and loose clothes away from the rotor when the power switch is "ON".

- Keep instructions for future reference.

- Warning! Do not touch the running rotors.

- Training by experienced adults is required for flying helicopters.

- Attention! Risk of eye injuries! Keep a safety distance of at least 1 or 2 metres.

Tip! SAFETY

Transmitter Battery Installation (*Make sure the power switch is on “OFF” position.)

1. Pull out the cover and take out the

charging plug from the transmitter.

2. Switch off the helicopter. Insert the charging

plug into the charging socket on the

helicopter.

3. Switch on the transmitter. The charging

process will begin automatically and the

green charging indicator will light up. Unplug

the charging plug after the charging indicator

turns off, charging is completed.

Charging Helicopter

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference, and

2)This device must accept any interference received, including interference that may cause undesired

operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Statements

Power Supply :

Rating : DC 9 V , 4.14 W

Batteries : 6 x 1.5 V "AA"/LR6/AM3 (not included)

Power Supply :

Rating : DC 3.7 V , 4,39 W

Batteries : 1 x 3.7 V Li-Po Rechargeable Battery Pack (included)

Capacity : 130 mAh

For further questions and problem, please visit our website：www.silverlit.com or www.silverlit-flyingclub.com.

Tool for Replacing

Tail Propeller

Spare Tail Propellers

Battery cover

4. Flight control:

Hover up

Hover down

EI-2378a

- Set the band on transmitter the same to the helicopter.

- Set the ON/OFF switch on helicopter to ON, the power indicator will flash, BE SURE THE TRANSMITTER IS “OFF” when turn on the helicopter.

- Place the helicopter on the ground with the tail point towards you and the nose facing away from you.

- Set the throttle stick on transmitter to MINIMUM throttle, and then turn on the transmitter.

2. DRIVE ON LAND:

- Steer the helicopter by adjusting the control stick of transmitter in different

combinations to perform different action (P 1).

- When the helicopter keeps turning clockwise(P 2), push and release the left

side of trim repeatedly till the turning stops and go straight (P 3).

- When the helicopter keeps turning counter clockwise (P 4), push and release

the right side of the trim repeatedly till the turning stops and go straight (P 5).

3. FLY IN AIR:

- Push the throttle stick to zone and press the “TAKE OFF” button.

The helicopter will take off from land (P 6).

- When you release the throttle stick on transmitter to minimium

throttle. The helicopter will return to driving mode.

Throttle stick Direction stick Action

Forward and accelerate

Forward left

Forward right

Tips for driving:

- The acceleration varies at different stick position.

- The turning speed and radius may vary at different stick position

combination.

- Operate only on flat, smooth (but not slippery), dry surfaces and low pile

carpet, as hair, carpet or dirt can affect the operation of the helicopter.

- Don't drive your helicopter in sand or through water or snow, if your

helicopter get wet, wipe with a towel and allow to dry completely.

Minimum Throttle position

For ages 10+

Ab 10 Jahre

A partir de 10 ans

Leeftijd vanaf 10 jaar

A partir de 10 años

Dai 10 anni in su

Silverlit SAS, Espace Green Parc, Route de Villepecle, 91280 Saint Pierre du Perray / France.

©2010 Silverlit. All rights reserved.

Stabilizer

Tail Propeller

Power Switch

Connecting Shaft

Main Rotor Blade

Front Wheel

Charging Socket

1

2

OFF/CHARGE

ON

Tool for replacing tail propeller

Caution:

Spare tail propeller

only to be replaced by an adult.

Roll Trimmer

Charging Indicator

“TAKE OFF” button

Direction Stick

Yaw Trimmer

Power Indicator

Cover and

Charging plug

Throttle Stick

Power Switch

Band Selector

Battery cover

OFF ON/CHARGE

A B

CHARGING POWER

TAKE OFF

1. ENVIRONMENT FOR FLIGHT:

Choose the place which meet the following condition:

1. Indoor environment with calm air condition. Beware of the air circulation from the air-conditioner.

2. Safety area: It is highly recommended that there is no electric fan, air-conditioner, reading lamp or other dangerous objects to flying.

P 1

P 2

P 4

P 6

P 3

P 5

Hover up and down:

When the helicopter flies steadily, you can slowly push the throttle stick

up to make helicopter fly higher, or lower the stick a bit to make

helicopter fly lower. Only small amounts of stick position change are

required for smooth flying.

Turn counter clockwise and clockwise:

Hold the helicopter at a height. Push the rudder stick toward left to turn

counter clockwise , and push the rudder stick toward right to turn

clockwise.

Accelerates & Decelerates:

If you turn the helicopter slowly to the counter clockwise, the

helicopter will decelerate. And when turned it to the clockwise, it will

accelerate.

Fly forward and stop:

The helicopter will take a slow forward speed when a gentle

Clockwise turn is made. To make it stop, it is sufficient to give a short

Counter clockwise turn command. By alternating this flight technique,

the helicopter can be directed anywhere and come back to it’s starting

position.

- Gently push the throttle up to raise your helicopter about 0.5 to 1

meter high.

- When the helicopter keeps move to left, adjust the roll trimmer counter

clockwise till the turning stops and go straight .

- When the helicopter keeps move to right , adjust the roll trimmer

clockwise till the turning stops and go straight .

1. ROLL TRIMMER

- Gently push the throttle up to raise your helicopter about 0.5 to 1 meter

high.

- When the helicopter keeps turning clockwise, adjust the yaw trimmer

counter clockwise till the turning stops and go straight .

- When the helicopter keeps turning counter clockwise , adjust the yaw

trimmer clockwise till the turning stops and go straight .

2. YAW TRIMMER

The power indicator on transmitter blinking. - Weak power of transmitter. - Change new batteries in transmitter.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Silverlit V-22 Osprey Radiobestuurbare helikopter. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Silverlit. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Silverlit V-22 Osprey Radiobestuurbare helikopter in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Silverlit Radiobestuurbare helikopters
Meer handleidingen voor Silverlit