Handleiding Skil 3065 HB Schroef-boormachine

Handleiding

10

and increase until the desired depth has been reached

• Mechanical gear selection e

- set selector D to desired speed

! actuate the gear selector while tool is running

slowly

1

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

2

- high speed

- lower torque

- for drilling small diameters

• WORKLIGHT H r

- WORKLIGHT H will illuminate in default low brightness

mode when the tool is turned on OR if WORKLIGHT

button G is depressed without turning the tool on.

Brightness can be switched from low to full or from full

to low by pressing the WORKLIGHT button G.

- Low brightness – turns o approx. 10s after on/o

switch is released

- High brightness - turns o approx. 600s after on/o

switch is released

! WORKLIGHT button G is disabled while the tool is

running. The brightness should only be switched

when the tool is not running.

! 

protection is activated (see below)

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

- the load is too high --> remove load and restart

- the battery temperature is not within the allowable

operating temperature range of -20 to +50°C --> 2

levels of the battery level indicator start ashing when

pressing button J7c; wait until battery has returned

within the allowable operating temperature range

- the battery is nearly empty (to protect against

deep discharge) --> a low battery level or ashing low

battery level ub is shown by the battery level indicator

when pressing button J; charge battery

! 



damaged

• Holding and guiding the tool t

! while working, always hold the tool at the grey-

coloured grip area(s)

- keep ventilation slots E 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits y

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

• of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

an electrical shock)

BATTERIES

• The battery supplied is partially charged (to ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

- SKIL battery: BR1*31****

- SKIL charger: CR1*31****

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

- when charging 4...40°C

- during operation –20...+50°C

- during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3

Read the instruction manual before use

4

Batteries may explode when disposed of in re, so do not

burn battery for any reason

5

Store tool/charger/battery in locations where temperature

will not exceed 50°C

6

Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A 2

- control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Battery level indicator 7

- press the battery level indicator button J to show the

current battery level 7a

! when the lowest level of the battery indicator

7b, the

battery is empty

! 

after pressing button J 7c, the battery is not

within the allowable operating temperature range

• Attaching belt clip 8

- attach the belt clip K to the drill with the supplied screw.

• Integrated bit clip L 2

- conveniently store hex bits.

• Strap xing M 2

- attach a wrist strap (not included) around your hand

when carrying the tool.

• Changing direction of rotation 9

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits q

! do not use bits with a damaged shank

• Torque control (VariTorque) w

- output torque will increase as clutch ring B is rotated

from 1 to 17; position C will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Skil 3065 HB Schroef-boormachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Skil. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Skil 3065 HB Schroef-boormachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Skil Schroef-boormachines
Meer handleidingen voor Schroef-boormachines

Veelgestelde vragen over Skil 3065 HB Schroef-boormachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Skil 3085 HB Schroef-boormachine

Handleiding

Skil 2421 AB Schroef-boormachine

Handleiding

Skil 3080 HC Schroef-boormachine

Handleiding

Skil 2430 AJ Schroef-boormachine

Handleiding

Skil 3008 GA Schroef-boormachine

Handleiding

Skil 3011 HB Schroef-boormachine

Handleiding

Skil 2470 AA Schroef-boormachine

Handleiding

Skil 3011 AA Schroef-boormachine

Gerelateerde categorieën