Handleiding Sony CFD-G55 Stereoset
Handleiding voor je Sony CFD-G55 Stereoset nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.
Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.
Handleiding
Loading…
Listening to the radio
1 Press POWER to turn on the player.
2 Press BAND•AUTO PRESET until the band you want appears in the display.
Each time you press the button, the indication changes as follows:
“FM” t “AM”.
3 Hold down TUNE + or – until the frequency digits begin to change in the
display.
The player automatically scans the radio frequencies and stops when it finds a
clear station.
If you can't tune in a station, press the button repeatedly to change the frequency
step by step.
Tip
If the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play in
monaural.
Changing the AM tuning interval
If you need to change the AM tuning interval, do the following:
1 Press BAND•AUTO PRESET until “AM” is displayed.
2 Press DISPLAY•ENTER•MEM ORY for 2 seconds.
3 Press BAND•AUTO PRESET for 2 seconds.
“AM 9” or “AM 10” appears.
4 Press TUNE + or – to select “AM 9” for 9 kHz interval or “AM 10” for 10 kHz interval.
5 Press DISPLAY•ENTER•MEMORY.
After changing the tuning interval, you need to reset your preset AM radio stations.
Presetting radio stations
You can store radio stations into the player’s memory. You can preset up to 30 radio stations, 20
for FM and 10 for AM in any order.
1 Press POWER to turn on the player.
2 Press BAND•AUTO PRESET to select the band.
3 Hold down BAND•AUTO PRESET for 2 seconds until “AUTO” flashes in the
display.
4 Press DISPLAY•ENTER•MEMORY.
The stations are stored in memory from the lower frequencies to the higher ones.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1 Press POWER to turn on the player.
2 Press BAND•AUTO PRESET to select the band.
3 Tune in a station you want.
4 Hold down DISPLAY•ENTER•MEMORY for 2 seconds until the preset number flashes in
the display.
5 Press PRESET + or – until the preset number you want for the station flashes in the display.
6 Press DISPLAY•ENTER•MEMORY.
The new station replaces the old one.
On the remote
1 Press BAND until the band you want appears in the display.
2 Tune in a station you want.
3 Hold down the number buttons that you want to preset the new station on for about 2 seconds.
To select the preset number over 10, press >10 first, then the corresponding number buttons.
You need to hold down the last number button to enter for about 2 seconds.
(Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.)
Playing preset radio stations
1 Press POWER to turn on the player.
2 Press BAND•AUTO PRESET to select the band.
3 Press PRESET + or – tune in the stored station.
On the remote
1 Press BAND.
2 Press the number buttons to to tune in the stored station.
To tune in a preset station over 10, press >10 first, then corresponding number buttons.
(Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)
To turn on/off the power
Press POWER.
To adjust the volume
Press VOLUME +, – (VOL +, – on the remote).
To listen through headphones
Connect the headphones to the i (headphones) jack.
Adjusting the audio emphasis
To select the sound characteristic
Press SOUND repeatedly to select the audio emphasis you want.
Choose To get
powerful, clean sounds, emphasizing low and high range audio
light, bright sounds emphasizing high and middle range audio
percussive sounds, emphasizing bass audio
the presence of vocals, stressing middle range audio
the whole dynamic range for music such as classical music
To reinforce the bass sound
Press POWER DRIVE WOOFER (WOOFER on the remote) to select or
in the display. is more effective. When POWER DRIVE
WOOFER function works, the button lights up.
To return to normal sound, press the button until the indication disappears from the display .
Notes
• While the sleeping timer is on, the POWER DRIVE WOOFER button does not light, even if the
WOOFER function works.
• When using the headphones, the WOOFER function does not work.
Falling asleep to music
1 Play the music source you want.
2 Press SLEEP.
3 Press SLEEP to select the minutes until the player goes off automatically.
Each time you press the button, the indication changes as follows: “60” t
“90” t “120” t “OFF” t “10” t “20” t “30”.
To cancel the sleep function
Press POWER to turn off the power.
Notes
• The backlight in the display does not light while the sleeping timer is on.
• When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will not go off until the tape
reaches the end.
Remote Control
Location of controls
FUNCTION
BAND
POWER
VOL +*, –
x
.,>
Z PUSH
OPEN/CLOSE
VOLUME –, +*
TUNE –, +
DISPLAY
ENTER
MEMORY
MODE
i
Number buttons
x
u*
POWER
LINE
OPR/BATT
Loading a CD
With the labeled side up
Inserting a cassette
With the side you want to
play facing upward
BAND
AUTO PRESET
SOUND
Display
Remote sensor
Total track number
Programmed track
Playing order
EF
Total playing time
Display
Press
x
u (X on the remote)
Press the button again to resume play after pause.
>
.
Z PUSH OPEN/CLOSE
> (forward) or . (backward) while playing until you
find the point.
> (forward) or . (backward) in pause until you find
the point.
a number button of the track on the remote.
*The button has a tactile dot.
POWER DRIVE
WOOFER
., >
PRESET –, +
N
X
SLEEP
MODE
TUNE+, –
WOOFER
SOUND
Press
xZ
M or m
X
Press the button again to resume play after pause.
xZ
SLEEP
LINE IN
(rear)
Playing a CD
1 Press POWER to turn on the player.
2 Load a CD in the CD compartment.
3 Press Z PUSH OPEN/CLOSE to close the CD compartment.
4 Press u (N on the remote).
The player plays all the tracks once.
To
stop playback
pause playback
go to the next track
go back to the previous track
remove the CD
locate a point while listening
to the sound
locate a point while observing
the display
locate a specific track directly*
* You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication by
pressing x.
Tip
To locate a track numbered over 10, press >10 first, then the corresponding number buttons on the
remote.
Example:To play track number 23, press >10 first, then 2 and 3.
Using the display
To check the total track number and playing time
Press DISPLAY•ENTER•MEMORY in stop mode (see fig. E).
To check the remaining time
Press DISPLAY•ENTER•MEMORY repeatedly while playing a CD. The display changes as
follows:
t the current track number and playing time
r
the current track number and the remaining time on the current track*
r
the number of tracks left and remaining time on the CD
* For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display.
Selecting the play mode
Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in
the display. Then proceed as follows:
To Select
repeat a single track “REP 1”
repeat all tracks “REP ALL”
shuffle play “SHUF”
repeat tracks “SHUF REP”
in random order
programme play “PGM”
repeat programmed tracks “PGM REP”
On the remote
When you’ve selected “PGM” or “PGM REP”, press the number buttons for the track you want
up to 20 tracks, then press N.
To cancel selected play mode
Press MODE until the selected mode disappears from the display.
To check the programmed track and playing order in the display
To check the order of tracks before play, press DISPLAY•ENTER•MEMORY.
Every time you press the button, the track number appears in the programmed order.
To change the current programme
Press x once if the CD is stopped and twice if the CD is playing. The current programme will be
erased. Then create a new programme following the programming procedure.
Tips
• You can play the same programme again, since the programme is saved until you open the CD
compartment.
• You can record your own programme. After you’ve created the programme, insert a blank tape and
press z to start recording.
Playing a tape
1 Press POWER to turn on the player.
2 Press xZ to open the tape compartment and insert a recorded tape. Close the
compartment. Use TYPE I (normal) tape only.
3 Press N.
To
stop playback
fast-forward or rewind the tape
pause playback
eject the cassette
Recording
1 Press POWER to turn on the player.
2 Press xZ to open the tape compartment and insert a blank tape. Use TYPE I
(normal) tape only.
3 Select the programme source you want to record.
To record from the CD player
Press x and load a CD (See “Playing a CD”).
To record from the radio
Press BAND•AUTO PRESET and tune in the station you want (See “Listening
to the radio”).
4 Press z to start recording.
(N is depressed automatically.)
To Press
stop recording xZ
pause recording X
Press the button again to resume recording.
Tips
• Adjusting the volume or the audio emphasis will not affect the recording level.
• For the best results, use the AC power as a power source for recording.
• To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press X.
3 Press N.
4 Press z.
5 Press X.
Connecting optional components
You can enjoy the sound from other components, such as TV, VCR and portable MD, CD player
through the speakers of this player.
Be sure to turn off the power of each component before making connections. For details, refer to
the instructions of the component to be connected.
Connecting a component
1 Connect the LINE IN jack on the rear panel of this player with the line output
jack or headphones jack of a TV, VCR or other component using the audio
connecting cable (RK-G129, RK-G136, not supplied).
2 Press LINE to display “LInE”.
3 Play the optional component connected to the LINE IN jack of the player.
Recording the sound from the connected components
1 Insert a blank cassette.
2 Press LINE to display “LInE”.
3 Press z.
Recording starts.
4 Play the optional component connected to the LINE IN jack of the player.
Note
Connect the cords firmly to avoid any malfunction.
Then do this
Press . or > to select the track that you
want to repeat, then press u.
Press u.
Press u.
Press u.
Press . or > then press DISPLAY•ENTER•
MEMORY for the tracks you want to programme
in the order you want up to 20 tracks (see fig. F).
Then press u.
Press . or > then press DISPLAY•ENTER•
MEMORY for the tracks you want to programme
in the order you want up to 20 tracks. Then Press
u.
Loading…
Beoordeling
Laat ons weten wat je van de Sony CFD-G55 Stereoset vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.Meer over deze handleiding
We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sony CFD-G55 Stereoset. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sony. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sony CFD-G55 Stereoset in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.
Specificaties
| Merk | Sony |
| Model | CFD-G55 |
| Categorie | Stereosets |
| Bestandstype | |
| Bestandsgrootte | 0.18 MB |
Alle handleidingen voor Sony Stereosets
Meer handleidingen voor Stereosets
Praat mee over dit product
Laat hier weten wat jij vindt van de Sony CFD-G55 Stereoset. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.