Handleiding Sony M-830V Cassetterecorder

Handleiding

3-229-699-51 (1)

Operating Instructions

CS

Kezelési utasítás (a hátoldalon)

Инструкция по эксплуатации

(см на обороте)

M-830V/740V

Sony Corporation ©2001 Printed in China

Microcassette

™

-

Corder

CSEnglish

A

(a)

B

(a)

C

(b)

(b)

AC power adaptor (not supplied)

CS

(c)

(d)

(c)

Preparing Power Sources

Choose one of the following power sources.

Dry Batteries (see Fig. A-(a))

Make sure that nothing is connected to the DC IN 3V jack.

1 Open the battery compartment lid.

2 Insert two R6 (size AA ) batteries with correct polarity and

close the lid.

To take out the batteries (see Fig. A-(b))

If the battery compartment lid is accidentally

detached (see Fig. A-(c))

Attach it as illustrated.

When to replace the batteries

For M-740V

Replace the batteries with new ones when the REC/BATT lamp

dims.

For M-830V

Replace the batteries with new ones when the BATT lamps go

off and the E lamp flashes.

The BATT lamps change as illustrated (see Fig. A-(d)).

Notes

• The unit will play back normally for a while, even after the E lamp

flashes. However, replace the batteries as soon as you can. If you do not,

the playback cannot be made with normal sound, noise may be

recorded and the recorded sound will not be loud enough (M-830V

only).

• In the following cases you do not need to replace the batteries:

– if the REC/BATT lamp, or BATT lamps flash with the playback sound

when you turn up the volume.

– if the E lamp lights momentarily when the tape starts running or at

the end of the tape (M-830V only).

– if the E lamp flashes during FF (CUE) or REW (REVIEW) (M-830V

only).

Battery life (Approx. hours) (EIAJ*)

Batteries Recording

Sony manganese R6P (SR) 7

Sony alkaline LR6 (SG) 24

* Measured valued by the standard of EIAJ (Electronic Industries

Association of Japan) (Using a Sony Microcassette)

Note

The battery life may shorten depending on the operation of the unit.

House current (see Fig. A-(e))

Connect the AC power adaptor to DC IN 3V and to a wall outlet.

Use the AC-E30HG AC power adaptor (not supplied). Do not

use any other AC power adaptor.

Note

Specifications for AC-E30HG vary for each area. Check your local voltage

and the shape of plug before purchasing.

Recording (see Fig. B-(a))

Make sure that nothing is connected to MIC.

1 Press the reset button of the TAPE COUNTER.

Note

The number in the tape counter will increase when playing back the

forward side, and decrease when playing back the reverse side.

2 Press xZ and insert a standard microcassette with the side

to start recording facing the lid (see Fig. B-(b)).

3 Select the desired tape speed.

2.4 cm for optimum sound (recommended for normal use):

A 30-minute recording can be made using both sides of the

MC-30 microcassette.

1.2 cm for longer recording time: A 60-minute recording can

be made using both sides of the MC-30 microcassette.

4 Choose recording sides.

To record on both sides

Slide DIR. so that the FWD indicator

turns green.

Recording will start form the side facing the

cassette holder window (forward side) and

switches automatically to the reverse side at

the end of the side (Auto Reverse).

Notes

• Make sure the tabs on both sides are not removed.

• Even if only the tab on the reverse side is removed, recording

cannot be made.

To record on a single side

Slide DIR. so that the REV indicator

turns green.

Recording will start form the side facing the

unit (reverse side).

Note

Make sure the tab on the reverse side is not removed.

5 Set VOR to H, L or OFF.

If you set VOR to H or L, the unit automatically starts

recording the sound and pauses when there is no sound

(you can save tapes and batteries).

H: To record at meeting or in a quiet and/or spacious place.

L: To record for dictation or in a noisy place.

When the sound is not loud enough, set it to OFF, or the unit

may not start recording.

6 Press z.

nN is pressed simultaneously and recording starts. While

the tape runs, the REC lamp (M-830V) or REC/BATT lamp

(M-740V) lights and flashes depending on the strength of the

sound.

Recording level is fixed.

At the end of the reverse side, recording stops and the unit turns

off automatically.

To Press or slide

Stop recording xZ

Start recording during playback z during playback (the unit becomes

in the recording mode)

Review the portion just recorded Push up CUE/REVIEW toward

REVIEW during the recording.

Release the button at the point to start

playback.

Pause recording Slide >PAUSE in the direction of

the arrow.

Take out a cassette xZ

Note

Select the 2.4 cm tape speed for recording, if you play back the recorded

tape with another unit. Otherwise, the sound quality may be changed.

Polarity of the plug

E

D

1

2

3

Notes on recording sides

• When recording on both sides, recording will not be made for a few

seconds while the tape is switching sides.

• When you open the cassette holder, the direction of the tape is reset to

the forward side.

• The DIR. switch cannot be used during recording.

Notes on VOR (Voice Operated Recording)

• The VOR system depends on the environmental conditions. If you

cannot get the desired results, set VOR to OFF.

• When you use the system in a noisy place, the unit will stay in the

recording mode. If the sound is too soft, on the contrary, the unit will

not start recording. Set VOR to H (high) or L (low) depending on the

conditions.

To monitor the sound

Connect an earphone to EAR jack. The monitor volume cannot

be adjusted by VOL.

To prevent a cassette from being accidentally recorded

over (see Fig. B-(c))

Break out and remove the cassette tabs. To reuse the cassette for

recording, cover the tab hole with adhesive tape.

Recording cue markers (M-830V only)

While recording, you can record a special signal on the tape to

mark a specific position.

At the desired position, press CUE MARKER to record a signal.

The REC lamp goes off and a signal will be recorded on the tape.

If you want to record a signal longer than that, press CUE

MARKER as long as you want.

During cue and review, you will hear the beep sound at the

signal position. During playback with the headphones plugged

in, you will hear the signal with low frequency sound at the

signal position.

Notes

• We recommend recording cue markers when there is a break in the

sound.

• The beep may sound differently depending on the marked position on

the tape because the winding speed varies from the beginning to the

end of the tape.

Playing a Tape (see Fig. C)

1 Insert a cassette with the side to start playing facing the lid.

2 Select the tape speed to the same speed as that used for

recording.

3 Press nN.

4 Adjust the volume.

At the end of the reverse side, playback stops and the unit turns

off automatically.

If you plug in headphones (not supplied) to the EAR jack, you

will get monaural output from both left and right channels.

To Press or slide

Stop playback/stop fast xZ

forward or rewind*

Pause playback Slide >PAUSE in the direction of the

arrow.

Play back only the DIR. so that the REV indicator turns green

reverse side and press nN.

Fast forward Slide CUE/REVIEW toward CUE during stop.

Rewind Slide CUE/REVIEW toward REVIEW during

stop.

Search forward during Keep CUE/REVIEW pushed down during

playback (CUE) playback and release it at the point you want.

Search backward during Keep CUE/REVIEW pushed up during

playback (REVIEW) playback and release it at the point you want.

Switch playback side DIR.

* If you leave the unit after the tape has been wound or rewound, the

batteries will be consumed rapidly. Be sure to depress xZ.

Note

If the tape is completely wound or rewound while searching forward/

backward during playback (CUE/REVIEW), the CUE/REVIEW switch

may not return to the center position when you release the switch. In this

case, push back the switch to the center to start playback.

To increase the playback speed (M-830V only)

Slide the FAST PB switch in the direction of the arrow. The

playback speed will be increased.

To return to the original speed, slide the FAST PB switch to the

original position.

At the end of the tape

In the recording or playback mode, the tape stops at the end of

the reverse side and the locked buttons will be released

automatically (Automatic shut-off mechanism).

After fast forward or rewind, be sure to set CUE/REVIEW back

to the center.

Recording/Playback with the

Connected Equipment

Recording from another tape recorder

Connect another tape recorder to the MIC jack using the RK-

G64HG connecting cord (not supplied).

Set this unit to the recording mode and another tape recorder to

the playback mode. In this case set VOR to OFF.

Recording with an External Microphone

Connect a microphone to the MIC jack. Use a microphone of low

impedance (less then 3 kilohms) such as ECM-T6 (not supplied).

When using a plug-in-power system microphone, the power to

the microphone is supplied from this unit.

Note

When recording with an external microphone, the VOR system may not

work properly because of the difference in sensitivity.

light

CS

When batteries are new

CS

Replace batteries

CS

When batteries become weak

CS

light

CS

go off

CS

go off

CS

flash

CS

Precautions

On power

•Operate the unit only on 3 V DC.

For AC operation, use the AC power adaptor recommended

for the unit. Do not use any other type. For battery operation,

use two R6 (size AA ) batteries.

On the unit

•Use only the (standard microcassettes) with this

unit. Non-standard cassettes cannot be used because their “L”

dimension (see illustration) is different (see Fig. D).

•Do not leave the unit in a location near heat sources, or in a

place subject to direct sunlight, excessive dust or mechanical

shock.

•Should any solid object or liquid fall into the unit, remove the

batteries or disconnect the AC power adaptor, and have the

unit checked by qualified personnel before operating it any

further.

•Keep personal credit cards using magnetic coding or spring-

wound watches etc. away from the unit to prevent possible

damage from the magnet used for the speaker.

•When you do not use the unit for long, remove the batteries to

avoid damage caused by battery leakage and subsequent

corrosion.

•If the unit has not been used for long, set it in the playback

mode and warm it up for a few minutes before inserting a

cassette.

If you have any questions or problems concerning your unit,

please consult your nearest Sony dealer.

Troubleshooting

Should any problem persist after you have made these checks,

consult your nearest Sony dealer.

A cassette cannot be inserted.

t The cassette is being inserted in the wrong way.

t nN has been already pressed.

Playback cannnot be made.

t The tape has reached the end of the reverse side. Press

DIR. to switch playback side to FWD.

t The batteries are weak. Replace both batteries with new

ones.

t The head is contaminated.

Recording cannot be made.

t There is no cassette in the cassette compartment.

t The tab on the tape has been removed. (Even if only the

tab on the reverse side is removed, recording cannot be

made.) To reuse the tape for recording, cover the tab hole

with adhesive tape. To record on one side only, insert a

cassette with the side to start recording facing away from

the lid (reverse side).

t The batteries are weak. Replace both batteries with new

ones.

t The head is contaminated.

t Improper setting of the VOR switch.

Recording is interrupted.

t The VOR switch is set to H or L. When you do not use

VOR, set it to OFF.

During CUE/REVIEW the tape stops or does not run.

You cannot fast-forward or rewind.

t The batteries are weak. Replace both batteries with new

ones.

The unit does not operate.

t The batteries have been inserted with incorrect polarity.

t The batteries are weak. Replace both batteries with new

ones.

t>PAUSE is slid in the direction of the arrow.

t The AC power adaptor is connected to the unit only and

you are going to use the unit on batteries.

No sound comes from the speaker.

t The earphone is plugged in.

t The volume is turned down completely.

The sound drops out or comes with excessive noise.

t The volume is turned down completely.

t The batteries are weak. Replace both batteries with new

ones.

t The head is contaminated. See “Maintenance”.

Tape speed is too fast or too slow in the playback

mode.

t Improper setting of the TAPE SPEED switch. Set it to the

same speed as that used for recording.

Tape speed is faster than the normal playback speed.

t The FAST PB switch (M-830V only) is slid in the direction

of the arrow.

Recording cannot be erased completely.

t The head is contaminated.

Maintenance (see Fig. E)

To clean the tape head and path

Press nN and wipe the head 1, capstan 2 and the pinch

roller 3 with a cotton swab, moistened with alcohol every 10

hours of use.

To clean the exterior

Use a soft cloth slightly moistened in water. Do not use alcohol,

benzine or thinner.

Specifications

Tape

(normal position type)

Recording system

2-track 1-channel monaural

Speaker

Approx. 3.6 cm (1

7

⁄16 in.) dia.

Tape speed

2.4 cm/s (

15

⁄16 ips), 1.2 cm/s (

15

⁄32 ips)

Frequency range

300 - 4,000 Hz (with TAPE SPEED switch at 2.4 cm/s)

Input

Microphone input jack (minijack/PLUG IN POWER)

sensitivity 0.22 mV for 3 kilohms or lower impedance microphone

Output

Earphone jack (minijack) for 8 - 300 ohms earphone

Power output (at 10% harmonic distortion)

250 mW

Power requirements

3 V DC batteries R6 (size AA) × 2/External DC 3V power sources

Dimensions (w/h/d)

Approx. 62.2 × 120.5 × 25.5 mm (2

1

⁄2 × 4

3

⁄4 × 1

1

⁄16 in.) incl. projecting

parts and controls

Mass

Approx. 130 g (4.6 oz)

Supplied accessories

Microcassette tape MC-30 (1) (European model only)

Batteries R6P (SR) (2) (European model only)

Carrying pouch (1) (M-830V and European model of M-740V only)

Design and specifications are subject to change without notice.

(e)

BATT

REC

BATT

REC

BATT

REC

1

About This Manual

The instructions in this manual are for the M-830V and M-740V.

Before you start reading, check your model number. The M-

830V is the model used for illustration purposes. Any

differences in operation are clearly indicated in the text, for

example, “M-830V only”.

CS

REV

FWD

REV

FWD

to the wall outlet

CS

Standard

CS

Non-standard

CS

Approx. 5 mm

CS

Only standard

microcassettes have a

small indention of side A.

CS

Approx. 2.5 mm

CS

Insert the # side

first for each

battery.

CS

EAR

Microphone

CS

z

> PAUSE

CUE/

REVIEW

xZ

VOR

TAPE SPEED

TAPE COUNTER

CUE MARKER

MIC (PLUG

IN POWER)

REC lamp (M-830V)

CS

REC/BATT lamp (M-740V)

CS

FAST PB

DIR.

EAR

nN

> PAUSE

CUE/

REVIEW

xZ

TAPE SPEED

FAST PB

Tape direction

indicators

CS

DIR.

xZ

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sony M-830V Cassetterecorder. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sony. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sony M-830V Cassetterecorder in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Sony Cassetterecorders
Meer handleidingen voor Cassetterecorders

Beoordeling

Gerelateerde producten

Handleiding

Sony M-560V Cassetterecorder

Handleiding

Sony WM-FX479 Walkman Cassetterecorder

Handleiding

Sony WM-EX150 Walkman Cassetterecorder

Handleiding

Sony WM-FX171 Walkman Cassetterecorder

Handleiding

Sony M-579V Cassetterecorder

Handleiding

Sony WM-GX320 Walkman Cassetterecorder

Handleiding

Sony WM-FX451 Walkman Cassetterecorder

Handleiding

Sony M-535V Cassetterecorder

Gerelateerde categorieën