Handleiding SunnCamp Silhouette Motor Voortent

Handleiding

attention to the position of the grey pole end support

eyelet.

T

he eyelet is for securing the fitting on the end of the

front canopy roof pole.

Remove the protective transit bags from the four captive

elbow fittings. The elbow fittings are tethered to the

f

lysheet by elastic cord and should not be removed. Make

sure you place the protective bags in the tent carry-bag

for safe keeping.

Insert both of the Black Shock

Corded Poles into the sleeves

marked with a black band. Then

insert the end of each pole into

the captive elbow fittings. Note:

the elbow fitting has a narrow

aperture for the black poles and a

wider aperture for the steel poles.

Next, connect a steel leg to each elbow fitting, making

sure that the two legs with the eyelets are at the front

and the eyelet is uppermost and facing the end of the

Awning.

Each leg end slots onto a pin on a ring. The pin and ring

are attached to a fixed webbing strap.

The ring is also used as the securing

point for the tent peg.

Starting with one pole, insert the

ring pin into the end of the pole.

Next, go to the other end of the pole

and insert the ring pin. Repeat with

the remaining two.

Insert the Grey Shock Corded Pole into the sleeve marked

with a grey band.

Both ends of the grey

poles are fitted with a

spike which is designed to

fit into the metal eye

fitted to the strapping,

attached to the steel leg.

Starting at one end of the

Awning, insert the spike

end into the eyelet.

Next, go to the other end of the pole and insert the spike

end into the opposite eyelet to bring the pole under

tension.

You can now attach the pole clips onto each pole to bring

the Awning flysheet into the correct shape.

Bring the Awning to an upright position by pegging out

the side guy ropes. (These may need to be re-pegged at

a later stage.)

You should now ensure that the entrances to the Awning

are closed with the zips fully secured. If this is not done

now, the Awning will be out of alignment when fitting

the Awning pegs.

Starting with the four corners, secure the base to the

ground using the Awning pegs. Next, secure all remaining

leg poles. Secure the flysheet to the ground by inserting

tent pegs through the pegging points.

When inserting into the ground, the

peg should be set at a 45 degree angle

a

way from the Awning. Pegs should be

hammered into the ground using a

suitable mallet and NOT pressed in with

t

he foot. Most bent pegs are caused by using your foot

rather than a mallet.

Pegs that are used to secure the door

o

pening can be left slightly raised.

This will allow easy hooking and

unhooking when opening or closing

the door.

Peg removal can be made easier if you use a suitable

extractor.

Secure each guy rope, positioning its Awning peg at a

suitable distance from the Awning.

Once in position, tighten the ropes equally

to bring the Awning into its natural shape.

DO NOT over tighten. To tighten, Hold the

rope above the slider and pull the slider up.

To release, again hold the rope above the

slider and pull the slider down.

Remember that all guy ropes are a trip hazard especially

in the dark.

To improve the awning’s rigidity, the roof tension poles

will be inserted inside the awning once the main erection

is complete.

Slot the tension poles together. Make sure that the

adjustable section, fitted with a lock screw, is loosely

fitted.

Next, insert the fixed end of the roof tension pole into

the left hand rear retainer sleeve. Keep the pole captive

within the retainer sleeve as you walk to the front of the

awning.

Raise the pole and insert the end section in to the left

hand front retainer sleeve. Carefully pull the pole and

adjustable section apart to bring them under tension

then lock in place by turning the lock screw clockwise.

Once in place, secure the tension pole with the captive

ribbon using a bow.

Repeat this, fitting a set to the right hand side.

The front entrance is single skinned and can be rolled to

one side. When closed, the zip cover/baffle must be

carefully pressed into place ensuring the Velcro tabs are

aligned and the skirt correctly positioned, secured by

Awning pegs, to avoid water ingress should it rain.

The Awning has a rear entrance

which should be closed whenever

your motorhome/campervan is

driven away.

The rear entrances are single

skinned and can be rolled back.

When closed, the zip cover/baffle

must be carefully pressed into

ROOF TENSION POLES

GUY ROPES

Peg

4

5°

AWNING PEGS

ENTRANCE

Strapping

Spike

Metal Eye

Leg PolePole

Pole

End Ferrule

Strap

Pin

Ring

Captive

Elbow

Fitting

S

teel

L

eg

place ensuring the Velcro tabs are aligned and the skirt

correctly positioned, secured by Awning pegs, to avoid

w

ater ingress should it rain.

Only one window is fitted to the Awning and has an

exterior cover rather than an internal curtain. This offers

two options.

Fully closed, it is fastened down by the two securing zips.

Note that the zip cover/baffle must be carefully pressed

into place to avoid water ingress should it rain.

Fully open, move the zips fully up to allow the fabric to

be held open with guy rope.

It is advisable to have a ‘Fire’ bucket filled with water,

placed outside the Awning. Hopefully it will never be

needed, but if it is, you will be glad you made the effort.

The Awning’s fabric is fire retardant, NOT fire proof and

therefore you must not smoke or use a naked flame in or

near the tent. This includes the traditional ‘camp fire’.

Guy ropes can cause a trip hazard and should be marked

so that passers by can see them.

Awning pegs are also a trip hazard and should not be left

‘half in’.

Cleaning…

Both inside and outside of the awning should only be

cleaned using fresh clean water and a damp cloth. Do not

use detergents or chemical cleaners.

Storing…

The awning is best stored in its original carry-bag,

however, if the awning is dismantled when wet, you MUST

thoroughly dry the awning as soon as possible.

After a wet pack-up, erect the awning as soon as possible

and allow its flysheet, guy ropes, any inner tent and of

course the carry-bag to fully dry naturally before

repacking everything away.

If stored when flysheet and/or guyropes are wet, the

awning will suffer from mildew and will become unusable.

Please note that damage caused by incorrect storage is

NOT covered by the manufacturer’s warranty.

Repairs…

Repairs to the awning should only be made by the

manufacturer’s recommended agents. Repairs made by an

unauthorised party will make the manufacturer’s warranty

void.

This Awning is designed for light use in normal weather

conditions. It is not suitable for storms, gales, sub zero

or tropical conditions.

Prolonged exposure to direct sunlight can weaken the

fabric of the Awning. To avoid the risk of UV

Deterioration, site the Awning in a shaded area, where it

will be protected from exposure to strong sunlight.

M

oisture collecting on the inside of the Awning fabric is

condensation caused by the occupier. It is NOT a sign of

leakage.

Note that condensation or damage caused by it, is NOT

c

overed by the manufacturer’s warranty.

This Awning has all its main seams hot air taped to help

prevent leakage. The remaining seams should be treated

with a seam sealant to maximize the Awning’s

weatherproofing.

Seam sealant should also be applied to main seams where

the tape has lost adhesion or has been damaged (tie

points or suspension points for example).

Seam sealant is available from your SunnCamp stockist.

To dismantle the Awning, simply reverse the erection

procedure. Do make sure that the entrance is left open to

allow air to escape when rolling the fly sheet up.

All poles must be dismantled and the dry Awning should

be carefully rolled prior to placing back in the carry-bag.

Care MUST be taken to ensure that the protective transit

bags are replaced to prevent the fabric being damaged by

the captive elbow fittings.

DISMANTLING

SEAMS

MOISTURE

UV DETERIORATION

STORM AND WEATHER SUITABILITY

CLEANING, STORING AND REPAIRS

SAFETY

WINDOWS

REAR ENTRANCE

ENTRANCES AND PORCHES

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je SunnCamp Silhouette Motor Voortent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met SunnCamp. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van SunnCamp Silhouette Motor Voortent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor SunnCamp Voortenten
Meer handleidingen voor Voortenten

Veelgestelde vragen over SunnCamp Silhouette Motor Voortent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

SunnCamp Mirage Voortent

Handleiding

SunnCamp Ultima 390 Voortent

Handleiding

SunnCamp Rotonde 300 Voortent

Handleiding

SunnCamp Ultima 260 Voortent

Handleiding

Vango Tuscany Air 400 Elements ProShield Voortent

Handleiding

Vango Balletto Air 390 Elements ProShield Voortent

Handleiding

Vango Braemar III 300 Voortent

Handleiding

Vango Galli III Low Voortent

Gerelateerde categorieën