Handleiding Technoline WS 9032 Weerstation

Handleiding

the time as 0:00 the date as TH.1., the moon icon, the weather icons (sun and clouds) will be

displayed. If the indoor temperature and humidity are not displayed after 15 seconds, remove

the batteries and wait for at least 1 minute before reinserting them. Once the indoor data is

displayed proceed to step 2.

2. Within 3 minutes of activating the Weather station, place the batteries into the transmitter (see

“How to install and replace batteries in the Thermo-Hygro outdoor transmitter“ above).

3. After inserting the batteries into the transmitter, the Weather station will start receiving data

from the transmitter. The outdoor temperature and humidity data should then be displayed on

the Weather station. If this does not happen after 3 minutes, the batteries will need to be

removed from both units and reset from step 1.

4. The Weather station can take up to 3 remote transmitters. If you have purchased additional

transmitters, follow step 2 for all extra transmitters. However, ensure that you leave 10

seconds in between the reception of the last transmitter and the set-up of the following

transmitter. The Weather station will number the transmitters in the order of set-up, i.e. the

first transmitter will have the temperature and humidity displayed with the number 1 against it

and so on.

5. Before all the transmitters are set up, there is a testing period, during which the display

switches quickly between all the received transmitters at random, according to which random

transmission it receives. The process will stop automatically if up to 3 transmitters are

received or no keys are pressed for a few minutes.

6. Once the remote data have been received and displayed on the Weather station, the DCF-77

time code reception is automatically started. This takes typically between 3-5 minutes in good

conditions. This time period is an excellent opportunity to locate the transmitter(s) in suitable

location(s) outdoors. In order to ensure sufficient 433 MHz transmission however, this should

under good conditions be no more than 100 meters from where the Weather station will be

finally positioned (see notes on “Positioning” and “433MHz Reception”).

IN key

OUT/+ key

ALM/DATE key

SET key

7. If after 10 minutes, the DCF time has not been received, use the SET key to manually enter a

time and date initially. The clock will automatically attempt to receive the DCF time at each full

hour. When this is successful, the received time will override the manually set time. The date

is also updated with the received time. (Please refer also to notes on “Radio controlled Time

Reception” and “Manual Time Setting”).

SNOOZE/CH key

Note:

In the event of changing batteries of the units, ensure the batteries do not spring free from the

contacts. Always wait at least 1 minute after removing the batteries before reinserting, otherwise

start up and transmission problems may occur.

RESETTING

The Weather Station and the Thermo-hygro transmitter need to be reset when one of the following

conditions occur:

Unsuccessful 433MHz signal reception.

Malfunction on the units.

Batteries replacement.

For resetting, remove all batteries from the units. Wait at least for 1 minute before powering up the

Weather station again. Proceed from step 1 in “Setting Up”.

DCF RADIO CONTROLLED TIME

The time base for the radio controlled time is a Cesium Atomic Clock operated by the Physikalisch

Technische Bundesanstalt Braunschweig which has a time deviation of less than one second in one

million years. The time is coded and transmitted from Mainflingen near Frankfurt via frequency

signal DCF-77 (77.5 kHz) and has a transmitting range of approximately 1,500 km. Your radio-

controlled Weather Station receives this signal and converts it to show the precise time in summer

or wintertime.

The quality of the reception depends greatly on the geographic location. In normal cases, there

should be no reception problems within a 1500km radius of Frankfurt.

Once the outdoor data reception test period is completed, the DCF tower icon in the clock display

will start flashing in the upper left corner. This indicates that the clock has detected that there is a

radio signal present and is trying to receive it. When the time code is received, the DCF tower

becomes permanently lit and the time will be displayed.

If the tower icon flashes, but does not set the time or the DCF tower does not appear at all, then

please take note of the following:

Recommended distance to any interfering sources like computer monitors or TV sets is a

minimum of 1.5 - 2 meters.

Within ferro-concrete rooms (basements, superstructures), the received signal is naturally

weakened. In extreme cases, please place the unit close to a window and/ or point its front or

back towards the Frankfurt transmitter.

During nighttime, the atmospheric disturbances are usually less severe and reception is

possible in most cases. A single daily reception is adequate to keep the accuracy deviation

below 1 second.

FUNCTION KEYS:

Weather Station:

The Weather Station has 5 easy to use function keys:

SET key

Press and hold the key to enter manual setting modes: LCD contrast, time zone, time

reception ON/OFF, 12/24 hour display, manual time setting, calendar, temperature °C/°F,

pressure hPa / inHg, relative pressure value, and weather icon sensitivity setting

Reset all MIN/MAX records

Stop the alarm during alarm ringing

Stop snooze mode

Back-light on

ALM/DATE key

Press and hold key for 3 seconds to enter the alarm setting mode

Active/de-active the alarm time

Stop the alarm during alarm ringing

Stop snooze mode

Display date

Back-light on

IN key

Press to toggle between MAX/MIN and current indoor temperature/humidity data

Press to set the alarm hour (inside alarm setting mode)

Decrease relative pressure value (within manual set mode)

Stop the alarm during alarm ringing

Stop snooze mode

Back-light on

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Technoline WS 9032 Weerstation. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Technoline. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Technoline WS 9032 Weerstation in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Technoline Weerstations
Meer handleidingen voor Weerstations

Veelgestelde vragen over Technoline WS 9032 Weerstation

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Technoline WS 9215 Weerstation

Handleiding

Technoline WS 6502 Weerstation

Handleiding

Technoline WS 6750 Weerstation

Handleiding

Technoline WS 9006 Weerstation

Handleiding

Technoline WS 6762 Weerstation

Handleiding

Technoline WS 9121 Weerstation

Handleiding

Technoline WS 9273 IT Weerstation

Handleiding

Technoline WS 6730 Weerstation

Gerelateerde categorieën