Handleiding Waring Commercial DMC201DCA Drankmixer

Handleiding

GROUNDING INSTRUCTIONS

• For your protection, Waring Commercial Mixers are equipped with

3-conductor cordsets.

• 120 Volt units are supplied with a molded 3-prong grounding-type

plug, and should be used in combination with a properly connected

grounding-type outlet as shown in Figure A.

If a grounding-type outlet is not available, an adapter, shown in Figure

B, may be obtained to enable a 2-slot wall outlet to be used with a

3-prong plug.

Referring to Figure C, the adapter must be grounded by attaching its

grounding lug under the screw of the outlet cover plate.

CAUTION: Before using an adapter, it must be determined that the

outlet cover plate screw is properly grounded. If in doubt, consult a

licensed electrician.

Never use an adapter unless you are sure it is properly grounded.

NOTE: Use of an adapter is not permitted in Canada.

GREEN/YELLOW: EARTH GROUND WHITE/BLUE: NEUTRAL BLACK/BROWN: LIVE

HOW TO USE YOUR WARING COMMERCIAL MIXER

Each mixing head of your Waring Commercial Mixer has an automatic on/off

switch that starts the motor. The motor is started when the container contacts

the on/off switch actuator and it is moved in an upward direction. The motor

will continue to run until the container is removed from the unit. A HIGH/LOW

speed selector switch is incorporated into each head. Mixer is designed to

operate with a rolled lip milk-shake container.

CLEANING/SANITIZING INSTRUCTIONS

1. Rinse containers thoroughly under running water. Add 8 ounces of clean

rinse water to containers. Place container in normal operating position on

mixer and run on high speed for two (2) minutes. Empty containers.

2. UNPLUG POWER CORD FROM ELECTRICAL OUTLET.

3. Loosen and remove thumbscrews and container rests. With both hands

reach around the mixer shaft. Place your fore fingers on each side of the

actuator knob in the indentation of the knob; placing your thumbs on the

top of the knob so as you pull the knob off of the switch stud you will not

hit the shaft.

4. Wash, rinse, and sanitize thumbscrews, on/off switch actuator knobs,

and containers. Sanitize these parts by immersing in sanitizing

solution for two (2) minutes. Shake off excess moisture and allow

parts to air dry.

5. Working from the top down, wash, rinse, and sanitize the portion of the

mixer housing situated directly over the containers and the portion of the

spindles above the agitators, using absorbent wiping cloths moistened with

cleaning solution, rinse water and sanitizing solution.

6. Reassemble on/off switch actuator knobs by placing actuator knob over

switch stud. With your other hand holding the back of the unit, to prevent

the unit from toppling over. Push actuator knob until you hear it snap in

place

7. Wash, rinse, and sanitize the agitators and the spindle bottoms as follows.

n Plug power cord into electrical outlet.

n Add 8 ounces of washing solution to containers and place in normal

operating position on mixer.

n Run on high speed for a minimum of two (2) minutes.

n Empty containers, and repeat two-minute run with 8 ounces of rinse

water.

n Empty containers. Run motors for a few seconds with empty containers

in normal operating position to spin off any excess moisture. Empty

containers. Do not rinse containers, spindles or agitators after sanitizing

is completed.

n Allow parts to air dry.

Wash, rinse, and sanitize as outlined above prior to initial use, and when-ever

mixer will not be used again within a period of one hour.

Surfaces of the mixer housing which are outside of the food-contact areas may

be cleaned as required, using wiping cloths moistened with cleaning solution, rinse

water, and sanitizing solution. UNPLUG POWER CORD FROM ELECTRICAL

OUTLET BEFORE CLEANING HOUSING. Prevent liquid from running into

housing by wringing all excess moisture from wiping cloths before using them.

Washing solutions based on non-sudsing detergents and chlorine-based

sanitizing solutions having a minimum chlorine concentration of 100 PPM are

recommended.

The following washing, rinsing, and sanitizing solutions, or their equivalents,

may be used.

REMOVAL AND REPLACEMENT OF MIXER HEADS

Each of the three mixing heads is individually removable for replacement or

repair.

TO REMOVE MIXER HEAD

1. Unplug unit from electrical outlet.

2. Remove rear cover panel from unit by removing the 7 (seven) screws.

A. B. C.

Circuit Grounding Conductor

Connected Properly

Grounding Prong

Grounding Lug

Adapter

Cover

Mounting

Screw

Cover of Ground Outlet Box

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE

WASHING: CALGON

®

CALGOLAC 1 TABLESPOONS/GALLON HOT (115˚ F)

RINSING: PLAIN WATER WARM (95˚F)

SANITIZING: CLOROX

®

INSTITUTIONAL 1 TABLESPOON/GALLON COLD (50˚ F

BLEACH 70˚ F)

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Waring Commercial DMC201DCA Drankmixer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Waring Commercial. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Waring Commercial DMC201DCA Drankmixer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Waring Commercial Drankmixers
Meer handleidingen voor Drankmixers