Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting. All rights reserved. Made in China
W-437
072815
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a
period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or
implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improper installation, surges in
electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-
ing materials (see figure 1).
WARNING:
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-
tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-
age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are pro-
vided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985
have supply wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded
type receptacle and is not intended for connection to a two wire ungrounded source of supply.
Owner’s Manual
Indoor Lighting Fixture
Installation Instructions
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely
supported.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic
lacquer which gives maximum protection against the weather. However, in time the brightness of
the brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass
fixture looking new for years to come, regularly apply a good quality, non-abrasive car wax to all
metal surfaces, giving the fixture an extra protective covering.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
FIGURE 2.
FIXTURE
WIRES:
Smooth
HOUSE
WIRES:
Black
(Hot)
HOUSE
WIRES:
White
(Neutral)
HOUSE
WIRES:
Bare
Copper
(Ground)
FIXTURE
WIRES:
Bare
Copper
(Ground)
FIXTURE
WIRES:
Ribbed
FIGURE 3.
PENDANT MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
meet all UL specifications.
1.
Turn off power at circuit box to avoid possible electric shock.
2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (
if applicable
) (see fig. 1).
3. Thread hex nut 1 (D1) onto mounting nipple (E) approximately 1/4 inch and insert lock washer (F),
then thread mounting nipple (E) onto mounting bar (A) and secure hex nut 1(D1).
4. Thread fixture loop (G) onto nipple (U) of fixture.
NOTE: Do not twist or kink wires when sliding fixture loop (G) downward.
5. Open one link on bottom end of chain (J). Attach to fixture loop (G). Securely close link on chain (J).
6. Thread screw collar ring (K) onto screw collar (L), then place canopy (M) over top of screw collar (L).
7. Lace wires up through every other link on chain (J) then through screw collar (L), canopy (M), and
mounting nipple (E).
8. O
pen one link on top end of chain (J). Attach to loop on screw collar (L). Securely close link on chain (J).
9. Identify color coding of fixture wires (see fig. 3).
10. Connect the smooth wire with marking printed or molded from the fixture with the black wire from
outlet (B) box
by wire connector (N), and wrap the wire connector (N) with electrical tape for a
more secure connection.
11. Connect the ribbed wire from the fixture with the white wire from the outlet box (B)
by wire
connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
12. Partially thread green grounding screw (O) into side hole (P) on mounting bar (A) (see fig. 1).
13.
Wrap grounding wire from fixture around green grounding screw stem (O) leaving enough excess
wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet
box (B) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape
for a more secure connection.
14. Tighten green grounding screw (O). Do not over tighten.
15. Remove screw collar ring (K) from screw collar (L) and secure screw collar (L) to mounting nipple (E).
16. Tuck wires inside outlet box (B).
17. Raise canopy (M) to ceiling and secure screw collar ring (K) to screw collar (L).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Spread fixture arms (W). (if applicable)
2. Thread nipple (K) into coupling (H).
3. Slide flat washer 1 (I1) and rubber washer 1 (Q1) over nipple (K). Raise glass (T) up to nipple (K)
protruding through opening in glass (T).
4. Carefully support glass (T) while securing rubber washer 2 (Q2) and flat washer 2 (I2), hex nut 2
(D2), decorative cap (R), and finial (S) to nipple (K).
5. Turn power back on at circuit box.
SEMI-FLUSH MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into mounting bar (B) approximately 1/4 inch (see fig. 1).
3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).
4. Remove the loop from canopy (F).
5. Remove cap nut (Q) from the canopy (F) for future use.
6. Identify color coding of fixture wires (see fig. 3).
7. Connect the smooth wire with marking printed or molded from the fixture with the black wire from
outlet (B) box
by wire connector (N), and wrap the wire connector (N) with electrical tape for a
more secure connection.
8. Connect the ribbed wire from the fixture with the white wire from the outlet box (B)
by wire
connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.
9. Partially thread green grounding screw (K) into side hole (L) on mounting bar (B) (see fig. 1).
10.
Wrap grounding wire from fixture around green grounding screw stem (O) leaving enough excess
wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet
box (B) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape
for a more secure connection.
11. Tighten green grounding screw (K). Do not over tighten.
12. Tuck wires inside outlet box (C).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Spread fixture arms (W). (if applicable)
2. Raise canopy (F) to ceiling allowing mounting screws (A) to protrude through openings in canopy
(F) and secure with cap nuts (Q).
3. Thread nipple (K) into coupling (H).
4. Slide flat washer 1 (I1) and rubber washer 1 (Q1) over nipple (K). Raise glass (T) up to nipple (K)
protruding through opening in glass (T).
5. Carefully support glass (T) while securing rubber washer 2 (Q2) and flat washer 2 (I2), hex nut 2
(D2), decorative cap (R), and finial (S) to nipple (K).
6. Turn power back on at circuit box.
FIGURE 1. For Pendant Mounting Option
LAMP
DECORATIVE
CAP (R)
FINIAL (S)
HEX NUT 2 (D2)
FLAT WASHER 2 (I2)
FLAT WASHER 1 (I1)
RUBBER WASHER 2 (Q2)
RUBBER WASHER 1 (Q1)
GROUND
WIRE
*NOT SUPPLIED
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
SIDE
HOLE (P)
WIRE
CONNECTORS (N)
OUTLET BOX SCREWS (C)
LOCK WASHER (F)
HEX NUT 1 (D1)
MOUNTING NIPPLE (E)
SCREW
COLLAR (L)
CANOPY (M)
CHAIN (J)
NIPPLE (U)
SCREW COLLAR
RING (K)
FIXTURE LOOP (G)
FIXTURE
ARM (W)
MOUNTING
BAR (A)
*OUTLET
BOX (B)
GREEN GROUNDING
SCREW (O)
GLASS (T)
COUPLING (H)
NIPPLE (K)
*NOT SUPPLIED
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
FIGURE 2.
GROUND
WIRE
LAMP
WIRE
CONNECTORS (N)
SIDE HOLE (P)
GREEN
GROUNDING
SCREW (O)
CAP NUTS (Q)
CANOPY (F)
CROSS
BAR (B)
MOUNTING
SCREWS (A)
OUTLET BOX
SCREWS (D)
DECORATIVE
CAP (R)
FINIAL (S)
HEX NUT 2 (D2)
FLAT WASHER 2 (I2)
FLAT WASHER 1 (I1)
RUBBER WASHER 2 (Q2)
RUBBER WASHER 1 (Q1)
FIXTURE
ARM (W)
GLASS (T)
COUPLING (H)
NIPPLE (K)
For Semi-flush Mounting Option
*OUTLET
BOX (C)
Praat mee over dit product
Laat hier weten wat jij vindt van de Westinghouse 6340300 Lamp. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.