Handleiding Westinghouse GSP625 Fornuis

Handleiding

24 25

TESTING THE

OPERATION

INSTALLATION

Once these checks have been completed, if the regulator

still fails to perform in a satisfactory manner it should

be replaced.

9. One by one, turn the knobs to minimum and screw in the

bypass screw (accessible when the knob is removed) until

a small stable ame results. Turn the knob to maximum

and then back to minimum to ensure that the correct

minimum flame is maintained.

10. Attach the LPG sticker to the cooker, near the gas supply

inlet. Cover the Natural Gas label that is factory tted.

TESTING THE OPERATION OF THE GAS COOKER

NOTE: You MUST test the cooker after installation, before

you hand it over to the customer.

You MUST have a manometer and a connecting tube.

CHECKING GAS SUPPLY

1. Check the manometer zero point is correct.

2. Connect the manometer to the cooker pressure test point.

This is located on the regulator or LPG inlet tting.

3. Turn on the gas supply and the electricity and try to ignite

the gas.

NOTE: It will take additional time to light the gas for the first

time as air needs to be purged from the pipes.

4. Check the operating pressure for the particular gas type

(see table on page 23).

FOR LPG COOKERS: Adjust the regulator if necessary (this may be

remote from the cooker).

FOR NATURAL GAS COOKERS

Regulators are supplied pre-adjusted and congured by the

component maker for use with Natural Gas. The appliance

installer is not required to make an adjustment to obtain the

correct outlet pressure setting.

An arrow on the base of the regulator indicates the direction

of gas flow when the inlet and outlet of the regulator are

orientated correctly. When the regulator has been tted check

for leaks from the connections with soapy water.

CHECKING THE FUNCTION OF THE REGULATOR

With the appliance operating check the outlet pressure:

• when all burners of the appliance are operating

at maximum,

• when the smallest burner of the appliance is operating

at minimum.

Under these conditions the outlet pressure should not vary

from the nominal outlet pressure by more than ±20% of the

nominal outlet pressure (ie ±0.20kPa for Natural Gas).

If the regulator appears to not be performing satisfactorily

then check the following points.

1. If the outlet pressure is consistently too low then the inlet

pressure may be too low and adjustment of an upstream

regulator may be needed, or an upstream regulator or

valve with insufcient ow capacity may be present in

the gas supply line. If this is suspected then it may be

necessary to repeat the checks whilst measuring both the

inlet and outlet pressure to determine if the inlet pressure is

in the range 1.13 – 5kPa.

Hex nut assembly,

fully screwed down

Hex nut assembly,

removed from

regulator and insert

disassembled

Insert oriented for

Natural Gas operation

Insert oriented for

LPG operation

2. Check that the regulator has been tted to the gas supply

line in the correct orientation, the arrow on the base of the

body indicates the direction of gas ow.

Once these checks have been completed, if the

regulator still fails to perform in a satisfactory manner it

should be replaced.

TESTING THE COOKER FEATURES

• Observe the ame appearance on each burner. If it is

much smaller or larger than expected, then the injector

size needs checking.

NOTE: When flame is unsatisfactory, then refer to the Electrolux

Technical Publications and correct the fault, if possible.

When maximum ame appearance is correct, then check the

turn-down setting on each burner. If the settings appear to be

incorrect, proceed as follows:

1. Adjust the bypass screw mounted on the body of each

hotplate control cock. This is accessible when the control

knob and the control panel are removed.

2. Check the ignition on all burners both separately and

in combination.

3. Check the operation of the electrical components,

if applicable.

4. If you are satised that the cooker is operating correctly,

then turn it off and show the customer how to use it.

Make sure you ask the customer to operate the clock

and controls.

NOTE: If the cooker cannot be adjusted to perform correctly,

then inform the customer of the problem and put a warning

notice on the cooker. If the problem is dangerous, then

disconnect the cooker. If there is a fault, then the customer

should be advised to contact the manufacturer’s local service

organisation or the retailer.

LPG CONVERSION – IMPORTANT (MODEL 635 ONLY)

This appliance is tted with Natural Gas burner injectors.

Please follow the procedure below if a conversion to suit

UNIVERSAL LPG is required.

The conversion kit contains 5 injectors and 1 LPG sticker.

1. Remove the hotplate burners to access the hotplate

injectors. Replace the factory tted NG injectors with the

appropriate injectors, as supplied.

2. Unscrew the hex nut from the regulator. The hex nut, brass

washer and nylon insert will disengage as an assembly.

3. Unclip the nylon insert from the nut assembly by rotating

the insert 1/4 turn, and pulling it free.

4. Turn over the insert, and clip back into position.

5. Ret the hex nut assembly to the regulator ensuring that

it is fully screwed down. The regulator is now set for

connection to LPG.

6. Turn on the gas supply and at each new connection check

for leaks using soapy water: each hotplate valve should

be turned on, one at a time, and the injector hole blanked

off for several seconds.

7. The operation of the regulator can be conrmed by

connecting a manometer to the pressure test point located

on the side of the regulator body adjacent to the outlet.

With the appliance operating check the outlet pressure

• when all burners of the appliance are operating

at maximum,

• when the smallest burner of the appliance is operating

at minimum.

Under these conditions the outlet pressure should not

vary from the nominal outlet pressure of 2.60kPa by more

than ±0.52kPa.

8. If the regulator appears to not be performing satisfactorily

then check the following points.

• If the outlet pressure is consistently too low then

the inlet pressure may be too low and adjustment of

an upstream regulator may be needed, or an upstream

regulator or valve with insufcient ow capacity may

be present in the gas supply line. If this is suspected

then it may be necessary to repeat the checks

whilst measuring both the inlet and outlet pressure

to determine if the inlet pressure is in the range

2.75 – 7.00kPa.

• Check that the insert has been tted correctly.

• Check that the turret screw is fully screwed down.

• Check that the regulator has been tted to the gas

supply line in the correct orientation, the arrow on the

base of the body indicates the direction of gas ow.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Westinghouse GSP625 Fornuis. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Westinghouse. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Westinghouse GSP625 Fornuis in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Westinghouse Fornuizen
Meer handleidingen voor Fornuizen

Veelgestelde vragen over Westinghouse GSP625 Fornuis

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Westinghouse WLG505WA Fornuis

Handleiding

Westinghouse WFE904SD Fornuis

Handleiding

Westinghouse PSP632S Fornuis

Handleiding

Westinghouse WFE914SA Fornuis

Handleiding

Westinghouse WLE622WA Fornuis

Handleiding

Westinghouse WLE642WCB Fornuis

Handleiding

Westinghouse WLE620WA Fornuis

Handleiding

Westinghouse WFE532WC Fornuis

Gerelateerde categorieën