Handleiding Westinghouse WBM4000WB Koel-vries combinatie

Handleiding

8 9

INSTALLATIONACCESSORIESFEATURES

1 Temperature control

2 Freezer light

3 Twist & Serve ice cube tray

and bin

4 Adjustable glass shelves

5 Freezer bins on telescopic

extension slides

6 Adjustable rollers

7 Stabilising foot

1

4

2

3

5

7

6

SINGLE DOOR ALL FREEZER (AF) FEATURES

Features may vary depending on model. Not all models will have features listed.

WFM3600WB illustrated

Adequate ventilation around your refrigerator

The diagram below shows the recommended airspace to

allow for ventilation of your refrigerator.

If you do not have a cupboard above the refrigerator

with a rear gap of minimum 100 mm (Y), recommended

clearance at the top of the refrigerator are as follows:

All models except WBE5160SC

If gap (Y) is not a minimum 100mm, then gap (X) increases

from 50mm to 90mm min.

Please note for model WBE5160SC

If gap (Y) is not a minimum 100mm, then gap (Z) increases

from 10mm to 45mm min.

When positioned in a corner area, spacing of at least

350mm on the hinge side will allow the doors to open

enough to enable the removal of bins and shelves.

Note: For those models with telescopic extension slide-out

bins, the clearance required increases from 350mm to

550mm for top mount and bottom mount models, and to

450mm for the all refrigerator model to allow full access to

the bins’ contents as well as bin removal.

(z)

50mm

30mm

30mm

Recommended

airspace

CABINET

DOOR

350mm

550mm for telescopic drawer models

(x)

(y)

NOTE:

Doors are designed to sit proud of cabinetry (not flush).

The clearances shown above are the recommended

minimum clearances. The clearance at the rear must not

exceed 75mm.

Installing your refrigerator

Your new refrigerator should arrive with the front adjustable

rollers wound down, to tilt the top backwards by about

20mm from upright. This will allow your refrigerator door to

self-close, providing a consistent closed seal.

Height adjustable front

rollers

Fixed rear rollers

20mm

The stability foot should also be wound fully up so it will not

interfere with the operation of the rollers (see diagram in

Step 3).

INSTALLING YOUR NEW APPLIANCE

CAUTION

The rollers are designed for forward or backward movement

only. They are not castors. Moving the refrigerator sideways

may damage your floor and the rollers.

1. Roll the refrigerator into place.

2. The top of the refrigerator should be tilted back by

20mm (see diagram on left). This will allow the doors to

self-close providing a consistent door seal.

3. If the refrigerator isn’t tilted back, you can adjust the

two front rollers by turning the large, plastic roller

nut. (see diagram below). One turn of the nut will

tilt the refrigerator back approximately 10mm. If you

have difficulty turning the roller nut, have someone

tilt the refrigerator back, so you have better access.

Alternatively, you can access the rollers from the side,

using a flat screwdriver. (See diagram below).

4. Check the alignment of the refrigerator to the

surrounding cupboards to see if it is level. You can

adjust the level with the rollers as detailed in step 3.

5. If you find your refrigerator rocks from corner to corner,

it means your floor is uneven. Find a piece of plastic or

hardboard etc. and pack it firmly under the roller.

6. On certain floor surfaces the refrigerator may roll

forward during operation. Where provided a “Roller

Stop” can be placed under the front rollers. If Roller

Stop is required, contact customer service on

1300 363 640.

7. You may now need to fine-tune the installation by

repeating Steps 3, 4 and 5.

Roller Stop

Large plastic

roller nut

Stability f

oot

wound up

Large plastic

roller nut

stability foot

wound up

Top of refrigerator

is level ie. horizontal

Adjust front rollers

for uneveness of floor

eg. wind this roller

down or up

Aligned to

cupboard

s

ie. even ga

p

aligned to

cupboards

ie. even gap

top of refrigerator is

level ie. horizontal

adjust front rollers

for uneveness of

floor eg. wind this

roller down or up

roller stop

rear gap

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Westinghouse WBM4000WB Koel-vries combinatie. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Westinghouse. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Westinghouse WBM4000WB Koel-vries combinatie in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Westinghouse Koel-vries combinaties
Meer handleidingen voor Koel-vries combinaties

Veelgestelde vragen over Westinghouse WBM4000WB Koel-vries combinatie

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Westinghouse WTB3700AG Koel-vries combinatie

Handleiding

Westinghouse WBB3700WG Koel-vries combinatie

Handleiding

Westinghouse WBE5100SC Koel-vries combinatie

Handleiding

Westinghouse WTM4200WB Koel-vries combinatie

Handleiding

Westinghouse WBB3700WA Koel-vries combinatie

Handleiding

Westinghouse WHE7670SA Koel-vries combinatie

Handleiding

Westinghouse WME3600SA Koel-vries combinatie

Handleiding

Westinghouse WHE5160SA Koel-vries combinatie

Gerelateerde categorieën