Handleiding Westinghouse WVG6314SD Oven

Handleiding

9INSTALLATION

Operating Pressures

Supply and operating pressures for various gases and

corresponding injector sizes for each burner.

GAS TYPE

SUPPLY

PRESSURE

(KPA)

NOMINAL

TEST POINT

PRESSURE

(KPA)

OVEN

INJECTOR

NG & SNG

1.13 - 5.00 1.00 1.50

UNIVERSAL

LPG

2.75

2.75 0.82

Testing the operation of the appliance

This product has an Electronic Burner Control with

a flame safeguard system, which includes a safety

shutdown function that operates when the presence of a

flame is not detected within a prescribed period.

It may be necessary to interrupt the operation of the

control system in order to facilitate purging of air from

the appliance.

During the purging procedure the product should be

closely monitored to ensure that the ignition spark can

be observed through the round hole in the left hand side

of the cover on the bottom of the oven, and that the

solenoid valve can be heard to open and close.

1. After connecting the gas and leak testing the gas

connection, plug in the service cord and turn on

the power.

2. Set the time of day clock (if fitted).

3. Purging procedure:

a. Turn on the oven.

b. The unit will commence sparking and the

solenoid valve will open for a short period. If a

flame is not established, the controller will shut

the solenoid valve and stop sparking, then pause

for a moment before repeating this cycle. At this

point if there is still no flame, the control system

will go into safety shutdown.

c. If the control system does go into safety

shutdown, turn off all the controls and switch off

the power supply for a few seconds.

d. Then turn the power back on and repeat steps 2.

to 3.c. until the gas ignites.

NOTE: If the power supply is not switched off, then a delay

of 90 seconds will be required after each safety shutdown

before a new ignition cycle can be attempted. For more

details about how the Electronic Burner Control works

refer to ‘Electronic Burner Control’.

4. Check the manometer zero point is correct.

5. Connect the manometer to the cooker pressure

test point. This is located on the regulator or LPG

inlet fitting.

6. Check the operating pressure (refer table above).

For LPG Cookers: Adjust the regulator if necessary

(this may be remote from the cooker).

For NG Cookers: The outlet pressure should not vary

from the nominal outlet pressure of 1.00kPa by more

than ±0.20kPa.

If the regulator apppears to not be performing

satisfactorily, then check the following points:

a. If the outlet pressure is consistently too low

then the inlet pressure may be too low and

adjustment of an upstream regulator may be

needed, or an upstream regulator or valve with

insufficient flow capacity may be present in the

gas supply line. If this is suspected then it may

be necessary to repeat the checks whilst

measuring both the inlet and outlet pressure to

determine

if the inlet pressure is in the range 1.13 – 5kPa.

b. Check that the regulator has been fitted to the

gas supply line in the correct orientation, the

arrow on the base of the body indicates the

direction of gas flow.

Once these checks have been completed, if the

regulator still fails to perform in a satisfactory manner

it should be replaced.

7. Observe the flame appearance on the burner. If it

is much larger or much smaller than expected, the

injector size may require checking. Where a flame is

unsatisfactory refer to the servicing instructions and

correct the fault if possible.

8. Check the operation of the timer, light and fan.

If the appliance cannot be adjusted to perform correctly,

inform the customer of the problem and affix an

appropriate warning notice to the appliance. If the

fault appears to be dangerous, the appliance should be

disconnected. However, if only a minor fault exists,

the customer may wish to use the appliance while

awaiting service.

The customer should be advised that, in the event of a

fault, they should contact the manufacturer’s local service

organisation or the retailer from whom the appliance

was purchased.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Westinghouse WVG6314SD Oven. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Westinghouse. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Westinghouse WVG6314SD Oven in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Westinghouse Ovens
Meer handleidingen voor Ovens

Veelgestelde vragen over Westinghouse WVG6314SD Oven

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Westinghouse WFE914SB Oven

Handleiding

Westinghouse PDR794 Oven

Handleiding

Westinghouse PSP632 Oven

Handleiding

Westinghouse WVEP9917DD Oven

Handleiding

Westinghouse WVEP9716SD Oven

Handleiding

Westinghouse WVE655SC Oven

Handleiding

Westinghouse GSP625 Oven

Handleiding

Westinghouse WVG6565SD Oven

Gerelateerde categorieën