2012 IQ200 Computer
Setup and Owners Manual - 11/11
TROUBLESHOOTING
CONDITION ACTION
Wheel moving but current speed does not
appear
Check/adjust sensor and magnet gap.
Battery is low –> replace
“ERR01” appears on display Battery low –> replace
Display is blank, very light or black Battery low –> replace.
Computer too hot –> move to cool area.
Display changes slowly Computer too cold –> move to warm area
IQ200 Specications
Operating Temperature 0° C ~ 40° C, ( 32° F ~ 104°F)
Storage Temperature -10° C ~ 50° C, ( 14° F ~ 122°F)
Battery (x2) 3 volt lithium, CR2032 cell
Weight 30.6 grams
Timer Range: 0~29 (hour): 59 (minute): 59 (second)
Current Speed Range: 0 ~ 99.9 KM/ 0~62 Mile
Average Speed Range: 0 ~ 99.9 KM/ 0~62 Mile
MAX Speed Range: 0 ~ 99.9 KM/ 0 ~ 62 Mile
(Trip) Distance Range: 0 ~ 999.99 KM/ 0~600 Mile
Odometer Range: 0 ~ 99999 KM/ 0 ~ 62000 Mile
1. Press FUNCTION until the “ODO” displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press SET to change to “KM/H” or “M/H”
4. Determine your Tire Size then nd the corresponding L (mm) in the chart below.
5. Press FUNCTION to move the cursor to the rst eld.
6. Press SET to change the 1st digit of 4 numbers for the L (mm).
Repeat steps 5 and 6 until the proper L (mm) is entered.
7. Press and hold FUNCTION for 3 seconds to exit programming.
SETTING CALORIES BURNED KCAL
This computer can estimate calories burned while riding. The estimate is based on weight,
gender, time ridden and average speed. IMPORTANT: The estimate is truly an estimate.
Actual calories burned will vary depending on many variables the computer does not
calculate such as heart rate.
1. Press FUNCTION until the “KCAL” displays.
2 Press and hold SET for >3 seconds to begin programming.
3. Press SET to select gender “MALE” or “FEMALE”.
4. Press FUNCTION to store gender.
5. Press SET to change weight unit “Kg” or “Lb”.
6. Press FUNCTION to begin entering your weight in unit selected.
7. Press or hold Set to change the weight. Range: 0 ~ 150 Kg, 0-330 Lb.
8. Press and hold the Function for 3 seconds to exit programming.
RESETTING THE ODOMETER ODO
If the battery is replaced, it is possible to update the odometer to the mileage on your bike
after replacing the battery.
1. Press FUNCTION until the “ODO” displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press FUNCTION until “00000” (ve zeros) and “ODO” appears on the screen
4. Press SET to change the appropriate numbers. Press FUNCTION to change cursor
position.
5. Repeat step 4 until the odometer is set.
6. Press and hold FUNCTION for 3 seconds to exit programming.
SETTING THE CLOCK CLK
1. Press FUNCTION until the “CLK” function shows.
2. Press and hold SET for >3 seconds to begin programming.
3. Press SET to change to “12H” or “24H” hour mode.
4. Press the FUNCTION to move the cursor to the hour eld
5. Press SET hour.
6. Repeat steps 4 and 5 to set Minutes and Seconds.
7. Press and hold the FUNCTION button for 3 seconds to exit programming.
GENERAL NOTES FOR PROGRAMMING ALL FUNCTIONS:
• Press and hold SET for 3 seconds to begin programming a function.
• Press SET to change the value of a selected eld. Press/hold SET to change value
rapidly.
• Press the FUNCTION button to move the cursor to the next eld.
• Press and hold the FUNCTION button for 3 seconds to exit programming.
SETTING THE WHEEL SIZE
BATTERY REPLACEMENT
Remove the computer from the handlebar mount. Use a coin to unscrew the battery door.
Turn counter-clockwise. Remove the old battery. Place a new battery (CR2032) into the
computer with the positive “+” marking of the battery facing up. Replace the battery door.
Follow these steps for replacing the sensor battery (CR2032).
L (mm)
Tire Size L (mm) Tire Size L (mm)
24 X 1.75 1890 27 X 1-3/8 2169
24 X 2.00 1925 650 X 20C 1938
24 X 2.125 1965 650 X 23C 1944
26 X 7/8 1920 650 X 35A 2090
26 X 1(59) 1913 650 X 38A 2125
26 X 1(65) 1952 650 X 38B 2105
26 X 1.25 1953 700 X 18C 2070
Tire Size L (mm) 26 X 1-1/8 1970 700 X 19C 2080
14 X 1.50 1020 26 X 1-3/8 2068 700 X 20C 2086
14 x 1.75 1055 26 X 1-1/2 2100 700 X 23C 2096
16 X 1.50 1185 26 X 1.40 2005 700 X 25C 2105
16 X 1.75 1195 26 X 1.50 2010 700 X 28C 2136
18 X 1.50 1340 26 X 1.75 2023 700 X 30C 2146
18 X 1.75 1350 26 X 1.95 2050 700 X 32C 2155
20 X 1.75 1515 26 X 2.00 2055 700C Tubular 2130
20 X 1-3/8 1615 26 X 2.10 2068 700 X 35C 2168
22 X 1-3/8 1770 26 X 2.125 2070 700 X 38C 2180
22 X 1-1/2 1785 26 X 2.35 2083 700 X 40C 2200
24 X 1 1753 26 X 3.00 2170 29 X 2.1 2288
24 X 3/4 Tubular 1785 27 X 1 2145 29 X 2.3 2326
24 x 1-1/8 1795 27 X 1-1/8 2155
24 X 1-1/4 1905 27 X 1-1/4 2161
CANNONDALE USA
Cycling Sports Group, Inc.
172 Friendship Road,
Bedford, Pennsylvania, 15522 , USA
(Voice): 1-800-BIKE-USA
(Fax): 814-623-6173
custserv@cyclingsportsgroup.com
CANNONDALE EUROPE
Cycling Sports Group Europe, B.V.
mail: Postbus 5100
visits: Hanzepoort 27
7570 GC, Oldenzaal, Netherlands
(Voice): + 41 61.4879380
(Fax): 31-5415-14240
servicedeskeurope@cyclingsportsgroup.com
CANNONDALE AUSTRALIA
Cycling Sports Group Australia Pty Limited
Unit 8, 31-41 Bridge Road
Stanmore, NSW 2048, Australia
(Voice): 61-2-85954444
(Fax): 61-2-85954499
CANNONDALE JAPAN
Namba Sumiso Building 9F,
4-19, Minami Horie 1-chome,
Nishi-ku, Osaka 550-0015, Japan
(Voice): 06-6110-9390
(Fax): 06-6110-9361
CANNONDALE UK
Cycling Sports Group
Vantage Way, The Fulcrum,
Poole, Dorset, BH12 4NU
(Voice): +44 (0)1202 732288
(Fax): +44 (0)1202 723366
CANNONDALE CONTACT INFORMATION
To begin using the computer, simply press the FUNCTION Button. Following installation,
the computer is activated automatically by a rotating wheel.
There are 2 power saving modes - 50% savings if no movement after 5 minutes, 100%
power savings after 30 minutes. Press the FUNCTION button to exit the power saving
modes prior to using the computer.
Press the FUNCTION button, to switch the computer through the following functions:
“CLK” – Clock feature, in 12/24 hr format
“TM” – Time ridden for 1 ride
“AVS” – Average speed for 1 ride
“MXS” – Maximum speed for 1 ride
“DST” - Distance ridden for 1 ride
“ODO” – Total miles ridden for all rides
“KCAL” – Calories burned (estimate) for 1 ride
“TM, AVS, MXS, DST and KCAL “ are recorded automatically as soon as the wheel moves.
Recording stops if the wheel stops. To clear this information, press and hold the SET
button in the “TM” mode.
MAIN DISPLAY AND FUNCTIONS
CURRENT SPEED
SPEED SCALE
SUB-DISPLAY
MODE
SET Button
(back of unit)
FUNCTION Button
FUNCTIONS DISPLAY
C
R
2
0
3
2
Praat mee over dit product
Laat hier weten wat jij vindt van de Cannondale IQ200 Fietscomputer. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.
beantwoord | Ik vind dit nuttig (37) Lees meer (Vertaald door Google)
Ik vind dit nuttig (31) (Vertaald door Google)
Ik vind dit nuttig (5) (Vertaald door Google)
beantwoord | Ik vind dit nuttig (12) (Vertaald door Google)
beantwoord | Ik vind dit nuttig (9) (Vertaald door Google)
beantwoord | Ik vind dit nuttig (7) (Vertaald door Google)
beantwoord | Ik vind dit nuttig (1) (Vertaald door Google)
Loading…
beantwoord | Ik vind dit nuttig (0) Lees meer (Vertaald door Google)
Ik vind dit nuttig (0) (Vertaald door Google)
beantwoord | Ik vind dit nuttig (0) (Vertaald door Google)
beantwoord | Ik vind dit nuttig (0)