Handleiding Casio G-Shock GD-350-1EF Horloge

Handleiding

Operation Guide 3403

E-49

Auto Light Precautions

Auto Light may not work properly if your arm is angled horizontally x

15˚ or more as shown in the illustration.

The presence of static electricity or magnetism can cause Auto

x

Light not to work. If this happens, try lowering your arm and

raising it back up again.

You may notice a rattling sound inside the watch when you angle

x

it towards your face. This is the sound of the Auto Light switch,

and does not indicate malfunction.

Auto Light remains enabled only for about six hours. After that it is

x

disabled automatically.

E-48

To enable or disable Auto Light

●

In the Timekeeping Mode, hold down

L

for at least

three seconds.

This will toggle Auto Light between enabled (Auto Light

ON indicator displayed) and disabled.

Auto Light ON indicator

E-47

Using Auto Light

When Auto Light is enabled, angling the watch towards your face at an angle of 40˚

or greater will illuminate the display automatically.

40˚ or greater

Note

Auto Light is disabled automatically while an alarm is sounding.

E-46

Illumination

You can use the procedure below to illuminate the display for easy reading in the

dark.

To illuminate the display

●

Press

L

to illuminate the display.

Note

Illumination will turn off automatically if it is on when an alarm time or the end of a

countdown is reached.

Light Use Precautions ◆

Frequent use of the light can shorten battery life.

E-45

●

Press

3

D

to toggle the setting between [VIB] and

[FLASH].

The Vibration indicator is shown on the display while

[VIB] is selected.

: Alert by vibration.

:

Alert by tone and fl ashing display

illumination.

●

To return to the Timekeeping Mode, press

4

A

.

To test vibration ◆

●

In the Timekeeping Mode, hold down

B

to perform the vibration operation.

Vibration indicator

E-44

●

To return to the Timekeeping Mode, press

4

A

.

Note

The above procedure affects the button operation tone only. The alarm, hourly time

signal, and time up alarm are not affected.

To change the alarm/timer alert method

●

In the Timekeeping Mode, hold down

1

A

for about

two seconds until the time zone setting screen

appears.

1

●

Press

2

C

11 times to display alert setting screen.

See “Confi guring Current Time and Date Settings”

(page E-15).

The screen will show either [VIB] or [FLASH].

E-43

●

Press

2

C

nine times to display the button

operation tone setting screen.

See “Confi guring Current Time and Date Settings”

(page E-15).

The screen will show either [KEY

] or [MUTE].

MUTE indicator

●

Press

3

D

to toggle the setting between

[KEY

] (ON) and [MUTE] (OFF).

When [MUTE] (OFF) is selected, a MUTE indicator is

displayed to indicate that the button operation tone

will not sound.

E-42

Other Settings

You can use the procedures in this section to turn the tone that sounds when you

press a button on or off.

You can also select either tone and display illumination fl ashing, or vibration as the

alert method for the alarm and timer.

To turn the button operation tone on or off

●

In the Timekeeping Mode, hold down

1

A

for about

two seconds until the time zone setting screen

appears.

E-41

Note

If a countdown was stopped part way through in the Timer Mode, the current

x

(stopped) countdown time will be displayed when you press A in the Timekeeping

Mode.

While a countdown is in progress, the display will show the countdown. You can

x

switch to display of the day of the week and day by pressing A.

To stop a tone/vibration alert operation

●

Pressing any one of the buttons will stop an ongoing tone/vibration alert

operation.

E-40

Note

If a previous countdown was stopped part way through in the Timer Mode,

x

pressing D will resume the countdown.

The x D button will be disabled if a countdown that was started in the Timer Mode

is still in progress.

An ongoing countdown (started in either the Timer Mode or Timekeeping Mode)

x

cannot be stopped or reset in the Timekeeping Mode.

To view the timer start time ◆

●

In the Timekeeping Mode, press

A

.

This will cause the timer start time (the start time you set with the procedure on

page E-36) to appear for one second in the display in place of the day of the

week and day.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Casio G-Shock GD-350-1EF Horloge. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Casio. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Casio G-Shock GD-350-1EF Horloge in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Casio Horloges
Meer handleidingen voor Horloges

Veelgestelde vragen over Casio G-Shock GD-350-1EF Horloge

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

Casio Edifice EFR-573DB-1AVEF Horloge

Handleiding

Casio Timeless Collection W-59-1VQES Horloge

Handleiding

Casio Vintage B640WB-1BEF Horloge

Handleiding

Casio Sheen SHE-3806D-7AEF Horloge

Handleiding

Casio G-Shock GW-9400-1DR Horloge

Handleiding

Casio Edifice EQB-1000D-1AEF Horloge

Handleiding

Casio Sheen SHE-4543GL-8AUEF Horloge

Handleiding

Casio Timeless Collection AQ-S800WD-1EVEF Horloge

Gerelateerde categorieën