Handleiding Coleman Elite Weathermaster 6 Tent

Handleiding

STITCH LINE

6. Rotate all eight Leg Poles upright and insert pin on

each web loop at the side locations as shown.

(Fig. 7 & 7A)

Fig. 6

Fig. 7

7A

Pin

7. Locate the plastic hooks at sides and

corners of tent, then snap onto Leg

Poles to attach. (Fig. 8)

9. Insert plastic stakes through web straps located

on both sides of tent, then drive in to secure.

(Fig. 10)

NOTE: It may be necessary to remove metal

stakes through web straps at side of tent and

screen room, pull tent taut, and drive in stakes

to secure.

Fig. 10

8. To stretch tent to finished size:

• Push in button on Leg Pole while

twisting lower Leg Pole section

counterclockwise (Fig.9);

• Pull up on top Leg Pole section until

tent is taut;

• Twist the lower Leg Pole clockwise

until the button locks into the center

or lowest hole;

• Repeat on remaining Leg Poles.

Fig. 8

Fig. 9

Button

Center Hole

Lower Hole

Lower

Leg Pole

Section

Upper

Leg Pole

Section

ELITE WEATHERMASTER

®

6 SCREENED TENT

MODEL 2000001588

Curved Ridge Poles with Red Markings in center sleeves

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter black pole with plastic tips);

then insert through zippered vertical pole sleeve on hinged side of

door. (Fig. 11)

2. Insert end of Vertical Door Pole into bottom hinge plate, apply

pressure to form a slight bow, then insert other tip of pole into top

hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

3. Assemble Door Pole (longer black pole with plastic cap tips); then

insert into zippered pole sleeve at top of door. (Fig. 14)

4. Insert end of Door Pole into top hinge plate, apply pressure to form

a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Fig. 11 Fig. 12 Fig. 13

Fig. 14

Fig. 15

Fig. 16

Fig. 1

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the door

facing the desired direction. Unzip doors. (Fig. 1)

4. Assemble eight, steel, shock-corded, Leg

Poles. Push down on steel button on tapered

end and insert into end with four holes.

NOTE: Make sure steel button locks into

third hole on pole as shown. (Fig.4)

5. Insert curved end of Leg Poles

(with red marking) into the

ends of the Ridge Pole

(with red marking). Insert

curved end of remaining

short Leg Poles into the

ends of the remaining

Ridge Poles. (Fig. 5 & 6)

Door

Ridge Pole with

Red Marking

Button in third hole

Fig. 4

Fig. 5

Fig. 2

Sleeve

with Red

Trim

Curved End of

Long Leg Pole

2. Pull four corners of tent taut, then secure by

driving stakes through web loops at an angle for

better anchoring. (Fig. 2)

Ridge Pole

with Red

Marking

Fig. 3

Sleeve

with Red

Trim

3. Assemble four, steel, shock-corded, curved

Ridge Poles. Insert Ridge Poles (with red

marking) into center sleeves on top of tent

with the red trim (Fig. 3). Insert the remain-

ing curved Ridge Poles into the other two

sleeves on top of tent.

Vertical Pole

Sleeve

Door Hinge

Pole

Sleeve

Top

Door

Hinge

Pole

Sleeve

Top

Door

Hinge

(continued on other side)

Pole Descriptions

Pole Pole Pole

Description Qty. Dia. Repair Kit Replacement Kit

Long Leg Pole, steel

(w/ red marking) 4 19mm N/A 5010000608

Short Leg Pole, steel 4 19mm N/A 5010000610

Curved Ridge Pole, steel

(w/ red marking) 2 19mm N/A 5010000607

Curved Ridge Pole, steel 2 19mm N/A 5010000609

Awning Pole, black,

fiberglass, metal tips 1 6.3mm 5010000543 5010000545

Door Pole, long, thin, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Vert. Door Pole, short, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Before you begin

Read all instructions before set up.

• Select a level site clear of rocks, branches, and other hard or sharp

objects, to install your tent.

WARNING: Keep clear of overhead power lines

.

• Do not set up your tent under trees because of potential lightning strikes

or falling tree limbs in inclement weather.

• Secure with all

stakes and guylines provided to prevent property damage

or personal injury.

• For best results in windy conditions, position narrow end of tent into

the wind.

• Enlist the help of at least one other person to assist you when it is time

to assemble the tent.

Self-Rolling Window Spring Descriptions

Color Code Description Qty. Length Replacement Part No.

Red 1 360mm 5010000624

Green 3 610mm 5010000627

Orange 2 670mm 5010000628

CAUTION: “Springs” may have sharp edges. Handle with care to avoid

injury. Keep out of reach of children.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Coleman Elite Weathermaster 6 Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Coleman. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Coleman Elite Weathermaster 6 Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Coleman Tenten
Meer handleidingen voor Tenten

Beoordeling

Veelgestelde vragen over Coleman Elite Weathermaster 6 Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Coleman Bi Space 400 Tent

Handleiding

Coleman Galiano 4 Tent

Handleiding

Coleman Sundome 12x10 Tent

Handleiding

Coleman Rondeau 3 Tent

Handleiding

Coleman Ciqala Tent

Handleiding

Coleman Evanston 6 Tent

Handleiding

Coleman Kohna Tent

Handleiding

Coleman Galiano 2 Tent

Gerelateerde categorieën