Handleiding Crain 204 Lijmpistool

Handleiding

No. 204 Edge Sealing Glue Gun

INSTRUCTION

MANUAL FOR

OPERATING INSTRUCTIONS: Read and save all instructions!

SAFETY FIRST: Use the glue gun in accordance with instructions only!

Hot melt glue sticks used with this glue gun should not be used in place of a

structural fastener. Hot melt glue sticks should not be used to hold heavy loads,

and should not be used in any application that will be exposed to heat. Some

hot melt glue sticks can re-melt and fail at temperatures as low as 60°C / 140°F.

Follow the glue stick manufacturer’s recommendations for any application.

To reduce risk of injury from burns or electric shock, wear protective clothing

including safety glasses, long sleeve work shirt, pants, gloves, and boots that

provide electrical insulation.

Glue gun nozzle and glue temperatures are hot (up to 220°C / 428°F). DO NOT

TOUCH THE NOZZLE OR HEATED GLUE! Safety glasses and protective cloth-

ing provide protection from the nozzle, heated glue, and heated glue droplets.

Provide time for heated glue to cool before touching. Hot glue can cause burns

until it has fully cooled. Some glue that appears to have cooled may still be

hot enough to burn. Use caution!

Stay alert and pay close attention to heated glue that is being applied. Burns are

possible from hot glue droplets from the glue gun, or droplets from any surface

onto which hot glue has been applied. Severe injury to eyes may result from hot

Hot melt glue adheres best to porous surfaces like wood. Sealed or ultra-smooth

surfaces, such as polished concrete, or painted surfaces, may reduce bond strength.

Some paint may reduce bond strength and require removal. Follow safe practices

for removal of lead based paint. Testing bond strength with scrap materials is advis-

able before beginning any job.

Some materials may be damaged by exposure to heat. Testing on scrap material

is recommended.

If heated glue drips excessively from the nozzle after the trigger is released, the

nozzle should be replaced. See instructions under Maintenance section below.

If undesirable glue strings develop from the nozzle as glue is applied, allow the glue

strings to cool. Afterwards, brush the strings off the nozzle using a piece of scrap

material. Do not remove strings with a hand, or jerk the gun around to break the

strings, as this can result in burns.

After applying glue, set the glue gun down on its stand, with the nozzle pointed

downward. When usage is complete, turn the toggle switch to the off position, and

disconnect the glue gun from power. Allow the glue gun to air cool on its stand.

Any hot-melt adhesive remaining in the gun after disconnecting from power should

remelt after heating. Do not pull on the glue stick to remove it from the gun.

CARPET EDGE SEALING INSTRUCTIONS: For carpet edge sealing, lift the edge

to be sealed with one hand. With the glue gun in the other hand, press the inside

corner of the tip against the edge of the carpet to be sealed. Hold the glue gun

at about a 45° angle to the carpet. Keep the upper wall of inside corner of the tip

against the edge of the carpet, and the lower wall of the inside corner of the tip in

contact with the backing of the carpet. (See gure 1 on front cover)

Glue is dispensed at the inside corner of the tip as the trigger is squeezed. Pull con-

tinuously, keeping the corner against the carpet edge for uniform application. This

takes practice. A test seam is a good idea, particularly on different carpet backings.

For best results, apply a small, continuous lm of adhesive along BOTH seam edges.

Applying excess adhesive may cause dribbling out of the seam and create hard spots.

MAINTENANCE - CHANGING THE NOZZLE: Do not attempt to change the nozzle

while the gun is cold, because hardened glue makes this very difcult. Damage to

gun is also possible. To change the nozzle, rst put on gloves to protect hands from

hot glue. Any excess glue stick extending from the back of the glue gun should be

cut off. Pre-heat the gun for about one minute, then disconnect power. Quickly

attach a wrench or pliers to the nozzle and turn counter clockwise to remove the

nozzle. Plug-in the glue gun and ush any remaining glue by repeatedly squeezing

the trigger until all glue has owed out. Unplug the glue gun, and allow cooling.

Screw in new nozzle and use wrench to tighten until snug. Don't overtighten as this

damages the seal rings.

The carpet edge sealing tip includes a jam nut to adjust the location of the outlet hole.

Tighten the whole tip assembly snug, then loosen one whole turn with a rst wrench.

Turn the tip assembly with the rst wrench to the desired position and hold. Next,

use a second wrench to tighten the jam nut to hold the tip assembly at that position.

ELECTRICAL SPECIFICATIONS: 120VAC - 100 WATTS

$3"*/500-4t.*-1*5"4$"t1)0/&

Carpet Edge

Sealing Tip

Figure 1

Inside

Corner

Upper

Wall

Lower

Wall

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Crain 204 Lijmpistool. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Crain. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Crain 204 Lijmpistool in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Crain Lijmpistolen
Meer handleidingen voor Lijmpistolen

Veelgestelde vragen over Crain 204 Lijmpistool

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Meister MHP36 Lijmpistool

Handleiding

Atten JQ-050 Lijmpistool

Handleiding

Ryobi R18GLU-0 Lijmpistool

Handleiding

Yamato 91843 Lijmpistool

Handleiding

Yamato 91846 Lijmpistool

Handleiding

Stickfast SL120 Lijmpistool

Handleiding

Yamato 95056 Lijmpistool

Handleiding

Yamato 91844 Lijmpistool

Gerelateerde categorieën